Dan Dugan Sound Design E-3A User Manual Download

Page: 29 / 82

Dugan Model E-3A User Guide

Connecting to a Computer

Wait a minute and if the list pane is blank, click

Refresh List

If the list pane remains blank, proceed to

Manually Add Unit

below.

If the list pane displays Dugan units, continue.

Click on the first unit in the list so it is highlighted.
The Network Parameters section displays information about that unit.
If you see

Unit Reachable: YES

, you are ready to use the Dugan Control Panel with

that unit. If you have additional Dugan units to connect, select the next unit in

the list and repeat this step. If you are finished with installation, proceed to

Chapter 6:

Dugan Control Panel Software

If you see

Unit Reachable: NO

, proceed to the next step.

Select the

Use DHCP

parameter.

Click

Send New Params to Unit

The Model E-3A will reboot.

Click

Refresh List

Highlight the unit in the list pane again.
If you see

Unit Reachable: YES

, this unit is ready to use with the Dugan Control Panel.

If you have additional Dugan units to connect, select the next unit in the list and

repeat Step 5. If you are finished with installation, proceed to Chapter 6:

Dugan

Control Panel Software

If you see

Unit Reachable: NO

, proceed to the next step.

10.

De-select the

Use DHCP

parameter.

11.

Match the first three groups of the IP Address with the computer, and assign

your own number to the last group.
This number

must not

have been assigned to another device in this network. You

may need to consult with the administrator of the network to determine this.

12.

Click

Send New Params to Unit

The Model E-3A will reboot.

13.

Click

Refresh List

14.

Highlight the unit in the list pane again.
If you see

Unit Reachable: YES

, this unit is ready to use with the Dugan Control Panel.

If you have additional Dugan units to connect, select the next unit in the list and

repeat Step 5. If you are finished with installation, proceed to Chapter 6:

Dugan

Control Panel Software

Summary of Contents for E-3A



















































































Search results

Summary of Contents for E-3A

Reviews:

Related manuals for E-3A

Brands by name

Popular brands

Dan Dugan Sound Design E-3A, User Manual

Search results

Summary of Contents for E-3A

Reviews:

Related manuals for E-3A

Brands by name

Popular brands