dallmeier MDF5450HD-DN Page 15 Commissioning Manual Download

Page: 15 / 56

Commissioning MDF5450HD-DN

Power Supply

The device can be operated with Power over Ethernet (PoE) and is compatible with all Power Sourcing Equipment (PSE) that is compliant with the

IEEE 802.3af PoE standard. Alternatively, the device can also be powered by an external 24 V DC power supply unit.

WARNING

Electrical shock caused by exposed electrical parts and due to the lack of or improper grounding/earthing

Risk of death or serious injury

➡

The installation of the device and the connection of peripheral equipment may only be carried out by qualified personnel and in a

voltage-free state.

➡

Before connecting or disconnecting an external DC power supply unit, make sure that the power supply unit is disconnected from the

mains socket (pull the power plug out of the socket).

➡

Carry out all protective measures for a standard-compliant grounding/earthing of the device in accordance with the currently

applicable DIN, VDE and ISO standards in order to ensure the safety of persons (protection against dangerous contact voltages).

NOTICE

Damage to the device due to improper power supply

Damage to electronic components or serious malfunctions

➡

Always ensure the correct polarity when connecting an external DC power supply unit.

➡

Do not operate the device with Power over Ethernet (PoE) if the device is powered by an external DC power supply unit.

Damage to the device or malfunctions due to the lack of or improper grounding/earthing

Damage to electronic components caused by lightning strikes and over-voltages (electrical surges) or malfunctions due to

electromagnetic interferences

➡

Carry out all protective measures for a standard-compliant grounding/earthing and a correct equipotential bonding of the device in

accordance with the currently applicable DIN, VDE and ISO standards in order to ensure the safety of the device (protection against

over-voltages) and its immunity to electromagnetic interferences (EMI).

Summary of Contents for MDF5450HD-DN
























































Search results

Summary of Contents for MDF5450HD-DN

Reviews:

Related manuals for MDF5450HD-DN

Brands by name

Popular brands

dallmeier MDF5450HD-DN, Commissioning Manual

Search results

Summary of Contents for MDF5450HD-DN

Reviews:

Related manuals for MDF5450HD-DN

Brands by name

Popular brands