manualshive.com logo in svg

DALBO POWERCHAIN 800, User Instructions, Page: 47 / 55

Share
Download
DALBO POWERCHAIN 800 User Instructions Download Page 47

 

POWERCHAIN 

 

Page 47 

 

Changing the wheel frame cylinder 

Fig. 26 

The disc harrow is folded out and lowered 

down onto an appropriate support (A) on 

either side of the machine, as shown in fig. 

24. The wheels are then lifted away from 

the supporting surface and re-lowered 

until they are resting on the ground. The 

pressure is taken off the tilting cylinder (B). 

 

1.

 

The hoses are disconnected from the cylinder. 

2.

 

The cylinder is supported. 

3.

 

The split pins in the pins are disconnected while the pins are removed. 

4.

 

The cylinder can be removed. 

5.

 

New or repaired cylinders can be fitted. 

 

After mounting, the tilt cylinder is activated until a small amount of movement can 

be felt in the cylinder. The cylinder is then activated in the opposite direction until 

the cylinder is back at the starting position. The cylinder is moved in this way a few 

times, whereupon the cylinder is moved out to the outer positions a few times to 

air the system out. 

 

 

Individuals must not be present within the action radius of the implement. 

A 

A 

B 

Summary of Contents for POWERCHAIN 800
























































Reviews:

No comments