background image

Introduction

2

Specifications Label

Power specifications as well as serial and model number information can be found on an 

ID label on the display, similar to the one shown in 

Figure 1

DAKTRONICS 201 DAKTRONICS DR. BROOKINGS, SD PHONE 800-325-8766

SUITABLE FOR SERVICING ONLY WHEN DE-ENERGIZED

PUET FAIRE L'OBJET D'UN ENTRETIEN UNIQUEMENT S'IL EST HORS TENSION

LL-4284957

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO

THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL

INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,

INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION

Figure 1: 

Specifications Label

Please have the assembly number, model number, and the date manufactured on hand 

when calling Daktronics customer service to ensure the request is serviced as quickly as 

possible. Knowing the facility name and/or job number will also be helpful.

Resources

Figure 2

 illustrates a Daktronics drawing label. 

This manual refers to drawings by listing the last 

set of digits. In the example, the drawing would 

be referred to as 

DWG-1007804

. All references to 

drawing numbers, appendices, figures, or other 

manuals are presented in bold typeface. 

Any drawings referenced in a section are listed 

at the beginning of it as shown below:

Reference Drawing:

System Riser Diagram .......................................................................................

DWG-1007804

Daktronics identifies manuals by the DD or ED number located on the cover page. 

Daktronics Nomenclature

Most display components have a white label that lists the part 

number (

Figure 3

). Part numbers will also appear on certain drawings. 

If a component is not found in the 

Replacement Parts (p�15)

, use 

the label to order a replacement. Refer to 

Section 6: Daktronics 

Exchange and Repair & Return Programs (p�16)

 if replacing or 

repairing any display component.

Main Component Labels

Part Type

Part Number

Individual circuit board

0P-XXXX-XXXX

Assembly; a collection of 

circuit boards

0A-XXXX-XXXX

Wire or cable

W-XXXX

Fuse

F-XXXX

Transformer

T-XXXX

Metal part

0M-XXXXXXX

Fabricated metal assembly

0S-XXXXXX

Specially ordered part

PR-XXXXX-X

Drawing Number

Figure 2: 

Drawing Label

0P-1127-0024

SN:  

     2465

02/19/12 Rev. 1

Figure 3: 

Part Label

Accessory Labels

Component

Label

Termination block for 

power or signal cable

TBXX

Grounding point

EXX

Power or signal jack

JXX

Power or signal plug for 

the opposite jack

PXX

Summary of Contents for TI-2022

































Reviews: