background image

Introduction

1

1  Introduction

This manual explains the operation of the Sportsound

®

 Rack (SSR) 200 Gen II. For 

additional information regarding the safety, installation, operation, or service of this 

system, refer to the telephone numbers listed in 

Section 6: Daktronics Exchange and 

Repair & Return Programs (p�23)

. This manual is not specific to a particular installation. 

Project-specific information takes precedence over any other general information found 

in this manual.

Important Safety Instructions

•  Read and understand all instructions before beginning the installation process.
•  Do not drop the control equipment or allow it to get wet.
•  Do not disassemble control equipment or electronic controls of the system; failure to 

follow this safeguard will make the warranty null and void.

•  Always turn off and/or unplug the control equipment when it is not in use. This keeps 

equipment protected from power spikes and lightning.

•  Never yank the power cord from the outlet. Grasp the plug and pull to disconnect.
•  Do not let any power cord touch hot surfaces or hang over the edge of a table that 

would damage or cut the cord. Arrange the cord with care so that it will not be 

tripped over.

•  Inspect control equipment for shipping damage such as rattles and dents, and verify 

that all equipment is included as itemized on the packing slip. Immediately report 

any problems to Daktronics; save all packing materials if exchange is necessary.

•  Keep equipment covered when possible to protect from dust and debris.

Resources

Figure 1

 illustrates a Daktronics drawing label. 

This manual refers to drawings by listing the last 

set of digits. In the example, the drawing would 

be referred to as 

DWG-1007804

. All references to 

drawing numbers, appendices, figures, or other 

manuals are presented in bold typeface. Any 

drawings referenced in a particular section are 

listed at the beginning of it as shown below:

Reference Drawing:

System Riser Diagram .......................................................................................

DWG-1007804

Daktronics identifies manuals by the DD or ED number located on the cover page. 

Daktronics has a searchable knowledgebase of common questions and troubleshooting 

tips: 

www.daktronics.com/en-us/support/systems/Audio%20Systems

 

Visit the Daktronics Support YouTube channel to learn 

how to properly operate Sportsound racks. Go to  

www.youtube.com/DaktronicsSupport

, and then click 

on Playlists to locate the 

Daktronics Audio - SSR-200 

Control System

 videos along with numerous other 

support videos.

Drawing Number

Figure 1: 

Drawing Label

Summary of Contents for SPORTSOUND SSR-200 GEN II









































Reviews: