background image

 

24

Repair & Return Program

For items not subject to exchange, Daktronics offers a Repair & Return Program. To send 

a part for repair, follow these steps:

1�  Call Daktronics Customer Service� 

United States & Canada: 1-800-DAK-TRON (325-8766)
Outside the U.S. & Canada: +1-605-275-1040

2�  Receive a case number before shipping� 

This expedites repair of the part.

3�  Package and pad the item carefully to prevent damage during shipment� 

Electronic components, such as printed circuit boards, should be placed in an 

antistatic bag before boxing. Daktronics does not recommend using packing 

peanuts when shipping. 

4�  Enclose:

•  name
•  address
•  phone number
•  the case number
•  a clear description of symptoms

5�  Ship to:

Daktronics Customer Service
[Case #]
201 Daktronics Drive, Dock E
Brookings, SD 57006

Daktronics Warranty & Limitation of Liability

The Daktronics Warranty & Limitation of Liability is located at the end of this manual.  

The Warranty is independent of Extended Service agreements and is the authority in 

matters of service, repair, and display operation. 

Summary of Contents for SPORTSOUND SSR-200 GEN II









































Reviews: