background image

 

 

MAN#650128 

Features 

 

The PAC-3100 is designed to control a single linear actuator/motor.  It is 

intended to be used to lift trunk lids and toppers/tanneau covers.  The PAC-3100 
has many convenient features which include: 

 

Three user programmable heights 

 

Stylish, lighted push button control 

 

Remote, ground activated, input lines to control the system with a remote system 

 

Safety auto reverse  

 

Auto move to position when the vehicle is turned on/ off 

 

Wiring 

BLACK 

 

         -  

Connect to a main ground location 

RED   

 

         -  

Connect to fused constant 12 volt power  

YELLOW 

 

         -  

Connect to switched 12 volt power 
(An accessory terminal will work for this) 

PURPLE 

 

         -  

Optional remote ground trigger for preset 3 

PINK   

 

         -  

Optional remote ground trigger for preset 1 

BROWN 

 

         -  

Optional remote ground trigger for preset 2 

WHITE w/ BLACK           -  

Optional remote ground trigger for manual down 

WHITE w/ RED 

         -  

Optional remote ground trigger for manual up 

PRESET BUTTONS         -  

To mating 4 pin connector 

 

Mounting 

The linear actuators should be mounted following the instructions supplied 

with them.  It is very important to mount the motors correctly or damage to the 
vehicle could result.  Remember that the motors should be mounted so they are 
completely closed when the trunk/cover being lifted is shut all the way.  Also 
insure that the motors can not raise too far and cause damage.   

The controller should be mounted inside the vehicle and all wires routed 

through the vehicle to appropriate connections or motors.   

The controller 

should NOT be mounted in the trunk area or under the cover being lifted for 
emergency service access. It is also recommended that remote manual 
up/down buttons be installed in case of emergency.  

 

The preset buttons require an oval hole to be cut for mounting, keeping in 

mind the buttons can be mounted horizontal or vertical.  

Drill two ½” holes 1.8” 

apart on center, then cut from hole to hole.  

 

1/2" Hole 

Cut dotted lines

 

Once the hole is cut insert the button panel from the front.  From the back, 

slide the two L-clamps over the studs and secure with the supplied lock washers 
and nuts.    

Summary of Contents for PAC-3100






Reviews: