background image

 

14 

MAN#650508B 

 

Tachometer Troubleshooting guide.

   

Problem   

 

Possible cause 

 

 

 

Solution   

 

 

 

 

 

Gauge will not light up 

Interconnect harness between speedometer and  Check 3 wire interconnect harness on the back of the gauges. 

 

 

 

  tachometer is unplugged. 

 

 

 

 

 

 

 

 

 

Clock will not keep time 

Orange wire does not have constant power. 

Connect to a location that has constant power. 

 

 

Gauge lights up, but tach 

Yellow wire is not connected properly.   

Check connection from yellow wire to tach signal wire. 

  will only show zero. 

Ignition system not grounded properly.   

Check engine and ignition system grounds. 

 

 

 

Gauge is not grounded properly.  

 

Check gauge and engine grounds. 

 

 

 

Tach signal type is not set correctly. 

 

Change the tach signal type (see instructions). 

 

 

 

Gauge is not calibrated 

 

 

Gauge must be recalibrated (see instructions).   

 

 

Tach reading is erratic or 

Tach signal wire is loose or broken. 

 

Check all wire connections and inspect wire for breaks. 

 jumps around. 

 

Poor ground connection. 

 

 

Check ground connection on tachometer, engine, and ignition  

 

 

 

 

 

 

 

 

system. 

 

 

 

Update rate is too fast. 

 

 

Reset display update speed slower. 

 

 

 

Tach reading is incorrect. 

Gauge is not calibrated correctly. 

 

Gauge must be calibrated (see instructions). 

 

 

Gear indicator is always 

 

Gears not programmed. 

 

 

Program gear indicator in setup.  (see instructions) 

 

Cruise Engage indicator 

Loose or incorrect connection to indicator wire. 

Check that the appropriate indicator wire has about 12 volts 

  does not work. 

 

 

 

 

 

 

  when the indicator should be off and about 0 volts when the 

 

 

 

 

 

 

 

  

 indicator should be on. 

 

 

 

 

 

Small gauge Troubleshooting guide.

   

Problem   

 

Possible cause 

 

 

 

Solution   

 

 

 

 

 

Gauge will not light up 

Interconnect harness between speedometer and  Check 3 wire interconnect harness on the back of the gauges. 

 

 

 

  gauge is unplugged. 

 

 

 

 

 

 

 

 

 

Gauge reading is erratic or 

Gauge signal wire is loose or broken. 

 

Check all wire connections and inspect wire for breaks. 

 jumps around. 

 

Poor ground connection. 

 

 

Check ground connection on gauge, engine, and sensor.  

 

Gauge reading is incorrect. 

Gauge is set up for wrong sensor type.   

Change sensor setting in setup. (see instructions).  

 

 

 

 

Poor gauge grounding. 

 

 

Repair or replace ground wire.  

 

 

 

 

WIRING COLOR CODE FOR SPEEDOMETER AND TACHOMETER: 
Color on GAUGE   

 

Stock harness color 

 

Function 

WHITE/RED 

 

 

varies with application 

 

speed sensor power out (if required)*

 

 

 

WHITE/BLACK 

 

 

BROWN/VIOLET 

 

 

security system indicator 

GREEN   

 

 

connects to supplied harness   

switch input 

GRAY 

 

 

 

see VSS section 

 

 

speed signal input 

WHITE 

 

 

 

WHITE/GREEN 

 

 

output speed signal 

PINK 

 

 

               BLACK/YELLOW   

 

engine indicator 

BLACK   

 

 

BLACK   

 

 

ground for gauge 

RED 

 

 

 

ORANGE/WHITE   

 

+12 volt power with key on 

ORANGE  

 

 

RED/ORANGE 

 

 

+12V battery power for clock   

 

YELLOW  

       

        

PINK 

 

 

 

tach signal input 

WHITE/GREEN 

                

GREEN/RED 

 

 

cruise set indicator 

*To avoid damage to motorcycle

, please see Speedometer, Tachometer, and Status and Warning Indicators sections for details on locating 

VSS, Tachometer, and indicator wires for 

most motorcycle applications

  

 

SERVICE AND REPAIR 

DAKOTA DIGITAL offers complete service and repair of its product line.  In addition, technical consultation is available to help you work through any questions or 

problems you may be having installing one of our products. Please read through the Troubleshooting Guide. There, you will find the solution to most problems. 

Should you ever need to send the unit back for repairs, please call our technical support line, (605) 332-6513, to request a Return Merchandise Authorization 
number.

  Package the product in a good quality box along with plenty of packing material.  Ship the product by UPS or insured Parcel Post.  Be sure to include the RMA number 

on the package, and include a complete description of the problem with RMA number, your full name and address (street address preferred), and a telephone number where you 
can be reached during the day.  Any returns for warranty work must include a copy of the dated sales receipt from your place of purchase.  Send no money.  We will bill you after 
repair.   

Dakota Digital 24 Month Warranty

 

DAKOTA DIGITAL warrants to the ORIGINAL PURCHASER of this product that should it, under normal use and condition, be proven defective in material or 

workmanship within 24 MONTHS FROM THE DATE OF PURCHASE, s

uch defect(s) will be repaired or replaced at Dakota Digital’s option.  

This warranty does not cover nor extend to damage to the vehicle’s systems, and does not cover removal or reinstallation of the product.  This Warranty does not 

apply to any product or part thereof which in the opinion of the Company has been damaged through alteration, improper installation, mishandling, misuse, neglect, or accident. 

This Warranty is in lieu of all other expressed warranties or liabilities.  Any implied warranties, including any implied warranty of merchantability, shall be limited to 

the duration of this written warranty.  Any action for breach of any warranty hereunder, including any implied warranty of merchantability, must be brought within a period of 24 
months from date of original purchase.  No person or representative is authorized to assume, for Dakota Digital, any liability other than expressed herein in connection with the 
sale of this product. 

WARNING:

 This product can expose you to chemicals including lead, which is known to the State of 

California to cause cancer and birth defects or other reproductive harm. For more information go to 

www.P65Warnings.ca.gov

 

 

 

Summary of Contents for MVX-8X00















Reviews: