Dakota Digital MVX-8X00, Manual

Page: 10 / 14

10
MAN#650508B
SPEED
Speed setup menu (continued)
unit

MPH/km/h Selection


Press and release the switch until “
unit
” is displayed, then press and hold the switch until the display blanks.

Release the switch. The display will show
UNIT
and
MI
for miles or
KM
for kilometers.

Press and release the switch until the desired setting is displayed.

Press and hold the switch to save the setting.
SERVICE
Miles or km to Next Service setup
The service mileage is a countdown mile meter. The service mile display can be disabled or can be set to count down
from 500
– 7500 miles. If the service mile is enabled and it gets to 0 miles, it will display “
SERVICE DUE
” each time the key is
turned on. If the push button switch is pressed and held while “  ” is displayed, the service miles will be reset.

Press and release the switch until “
SERVICE
” is displayed, then press and hold the switch until “  ” is displayed.

Release the switch. The current setting will be displayed. (“
OFF
” or a mileage from 500 – 7500 in increments of 500.)

Press and release the switch until the desired setting is displayed.

Press and hold the switch to save the setting.
ODO PRESET
Odometer preset
The odometer can be preset by the customer within the first 100 miles. Once the odometer has more than 100 miles the
menu option will no longer be displayed. Make sure you have correctly selected the units to be either MPH or km/h first. The
odometer will be set in the selected units. Once you have preset the miles you cannot change it again.
WARNING!!: This
only allows setting odometer to the nearest mile. Do not use tenths! For example a mileage of 65432.1 should be set
to “
065432
”
using this method. If the tenths digit is used, the odometer will read 10 times too high.

Press
and release the switch until “
ODO PRESET
” is displayed, then press and hold the switch until the display blanks.

The current miles will be displayed with the left most digit flashing.

Press and release the switch to increment the digit. Press and hold the switch to move to the next digit to the right.

Continue until the right most digit has been set. Press and hold the switch and the display will show “
save? no
”.

Press and hold the switch while “
save? no
” is displayed to go back and continue changing the odometer display. Turn the
key off to cancel any changes.

Press and release the switch to change to speed display to “
save? yes
”. Press and hold the switch while “
save? Yes
” is
displayed to save the current odometer reading.
tach
Tachometer setup menu

Press and release the switch until “
tach
” is displayed, then press and hold the switch until the display blanks.

Release the switch. The display will
show “
warning
”, “
cylinder
”, “
signal
”, or “
DONE
”.

Press and release the switch to change the selection, press and hold the switch to select it.
warn

High RPM warning setup


Press and release the switch until “
warning
” is displayed, then press and hold the switch until the display blanks.

Release the switch. The display will
show “
hi
”, the current RPM warning (2200 – 8200), and “
warning
”.

Press and release the switch to change the value, press and hold the switch to select it.
cylinder

Engine cylinder setup


Press and release the switch until “
CYLINDER
” is displayed, then press and hold the switch until the display blanks.

Release the switch. The display will
show “
engine
” and the current engine cylinder setting (1 – 16) followed by “
CYLINDR
”.

Press and release the switch to change the value, press and hold the switch to select it.
signal

Tachometer signal setup


Press and release the switch until “
signal
” is displayed, then press and hold the switch until the display blanks.

Release the switch. The display will
show “
normal
” or “
LO VOLT
”. The normal setting should be used.

Press and release the switch to change the value, press and hold the switch to select it.