background image

 

MAN #650778  

11 

FUEL Fuel level setup menu 

A low warning pump will be displayed above the Speed and the fuel bar will flash when 10% or lower is reached 

When >FUEL

the switch.

The options to select between are SENDER ,  RANGE TO EMPTY

TEST and

 

Press and release the switch to change the selection; press and hold the switch to select it. 

SENDER Fuel sender selection 

 

When  >SENDER

 hold the switch unti

 the switch. 

 

The options to select between are  OFF   HD 2004 ,  HD 2011 ,  DYNA 11 ,  HD 2018 ,  CUSTOM

SPORTSTER  

 

Press and release the switch to change to the proper sender. 

 

Press and hold the switch 

n release the switch 

 

Exit fuel setup to confirm fuel selection 

o

 

CUSTOM is only for rare occasions if a stock sender is not being used! 

o

 

If CUSTOM is selected, you will be prompted to Program. 

o

 

 release the switch 

o

 

The d

 

o

 

 

o

 

The display will 

 

o

 

Add fuel to 1/3 of a tank 

o

 

he switch 

o

 

The display 

 

o

 

Add fuel to 2/3 of a tank 

o

 

 

o

 

T

 

o

 

Top off the tank 

o

 

 

o

 

Exit setup to confirm fuel selection. 

 

RANGE TO EMPTY Distance to empty (fuel) setup 

  The range to empty option will calculate an estimate of miles until empty. 
  This will vary on riding conditions and will change as it continually monitors fuel usage and speeds. 
  The process will begin with a full tank, and then enter into the FUEL menu, RANGE TO EMPTY, and LEARN RESET. 
  Once the reset has been done, you may ride until the tank is below ¼. 
  This can be done over multiple trips as long as no fuel is added until the level is less than 25%, then it must be filled. 
  When the system is working, the DIST TO E screen will have a countdown odometer. 
  When the DIST TO E odometer reaches 35 miles or 56km, it shows 

 

  Once the RANGE TO EMPTY is working, you may fill your tank normally, when needed. 

 

When  >RANGE TO EMPTY

displayed, then press and hold the swit

 

 

The 

 

 

 

Press and release the switch to select an option. 

 

Press and hold the switch 

 release the switch. 

 

If O

LEARN RESET

 

 

e while riding.  It can be reset again if the process failed. 

o

 

Once the fuel tank is full, you ma

 

o

 

Press and hold the sw

 

o

 

Exit setup 

o

 

Cycle the ignition then you may ride until fuel is less than 25%.

 

o

 

Only then, you may refill the tank.  Once full, the process will complete itself.

 

o

 

Filling and refilling must be done the same way, either both on kick stand or both upright.

 

TEST Gauge reading test 

 

TEST

 

 

o

 

 

e a value in numbers. 

o

 

 

 

Exit setup. 

Summary of Contents for MLX-9X14 Series
















Reviews: