8
MAN#650678:C
PRESET ODO Odometer preset
The odometer starts at zero, but can be preset by the customer within the first 100 miles (161 km) of riding.
After riding more than 100 miles (161 km), the menu option will no longer be displayed.
Correctly select the units to be either MPH or km/h FIRST, as the odometer will be set in the selected units.
The preset is in full miles or kilometers only, no tenths
The odometer can be reset multiple times within the first 100 miles (161 km) of riding.
•
When “>PRESET ODO” is displayed, press and hold the switch until “RELEASE” is displayed and release the switch.
•
The current miles will be displayed with the left most digit flashing.
•
To change the flashing number, press and release the switch to the desired number.
•
Press and hold the switch until “RELEASE” is displayed, then release the switch.
•
Repeat the process of until the right most digit has been set.
•
With the far right number flashing, press and hold the switch and the display will show “>SAVE ODO? NO”.
•
Verify the small odometer at the bottom is what you want set.
o
If incorrect, hold the button until “RELEASE” is displayed, then release the switch.
o
You can now step through the process again and correct your readings.
o
Turning the key off at any time will discard any attempted odometer settings.
•
If the odometer is correct at the “>SAVE ODO? NO” screen, press and release the switch until “SAVE ODO? YES”.
•
When “>SAVE ODO? YES” is displayed, press and hold the switch until “RELEASE” is displayed and release the switch.
•
Exit setup.
TACH Tachometer warning setup
•
When “>TACH” is displayed, press and hold the switch until “RELEASE”, then release the switch.
•
When “>HIGH WARNING” is displayed, press and hold the switch until “RELEASE”, then release the switch.
•
The default high warning of “*5500” is shown with a range of 2200 – 8400 RPMs.
•
Press and release the switch to increase the value by 100 RPMs.
•
Once reaching 8400 RPMs the next number will roll back to 2200 RPMs.
•
Once you choose a valid warning, press and hold the switch until “RELEASE”, then release the switch.
•
Exit menu.
TEMP Head temperature unit setup menu
(Only valid if ECM is sending out cylinder head temp data)
•
When “>UNIT” is displayed, press and hold until “RELEASE”, then release the switch.
•
The options are “F”, “C”, or “BACK”.
•
Press and release to select the unit.
o
Setting this temperature unit will also change the air temp unit if a MBM-17 is installed with temp sender
•
Press and hold until “RELEASE”, then release the switch to exit
FUEL Fuel level setup menu
A low warning will be displayed on either the fuel gauge or Speed Top as a red band warning when fuel reaches 10%.
•
When “>FUEL” is displayed, press and hold the switch until “RELEASE”, then release the switch.
•
The options to select between are “SENDER”, “RANGE TO EMPTY”, “TEST”, and “BACK”.
•
Press and release the switch to change the selection, press and hold the switch to select it.
SENDER Fuel sender selection
•
When “>SENDER” is displayed, then press and hold the switch until “RELEASE”, then release the switch.
•
The options to select between are “SPORTSTER”, “DYNA 04”, “DYNA 08”, “CUSTOM” and “BACK”.
•
Press and release the switch to change to the proper sender.
•
Press and hold the switch until “RELEASE”, then release the switch
•
Exit fuel setup to confirm fuel selection
o
CUSTOM is only for rare occasions if a stock sender is not being used.
o
If CUSTOM is selected, you will be prompted to program.
o
When “>PROGRAM” is displayed, press and hold until “RELEASE”, then release the switch.
o
The display will show “SET EMPTY”
o
With an empty tank, press and hold until “RELEASE”, then release the switch.
o
The display will show “SET FULL”
o
Fill the tank
o
Press and hold until “RELEASE”, then release the switch.
o
Exit setup to confirm fuel selection.
WARNING LIGHT Low fuel light setup
The low fuel indicator can be turned on or off
•
When “>WARNING LIGHT” is displayed, then press and hold switch until “RELEASE”, then release the switch
•
The options to select from are “OFF”, “ON”, and “BACK”
•
Press and release the switch to change the option
•
Press and hold the switch until “RELEASE” to save
