background image

Model 9016 X-Purge Operator Interface 

Daisy Data Displays, Inc. 

February 2022 

D010-000002 

11.

Slowly increase air pressure

 with the regulator until the purge process stops.

Note Pressure the pressure at which the purge process stops.

The Purge Status LED will flash red and display an error code -

 [2 – 2]

 (over

pressure) or 

[3 –2]

 (over-flow).

12.

Remove AC power

 from the enclosure for a minimum of 30 seconds. Decrease

the pressure reading on the pressure gauge by 5 PSI.

This change may vary slightly on some units; if in later testing the unit fails with

an 

[3 –2]

 (over-flow) error code, decrease the inlet pressure by another 2 PSI.

Note Pressure for use during start-up.

13.

Re-apply AC power.

 The Purge Status LED will illuminate yellow and should purge

for a minimum of 8 minutes. Time will vary according to the flow rate of the air

into the enclosure.

14.

After the purge is complete

, the Purge Status indicator will illuminate green.

AC power is now applied to the internal electronics to power on the display or PC.

15.

If the purge status light blinks red

, refer to Table 6.1 X-Purge Status Light Key on

page 12 for error code details.

Summary of Contents for 9016 X-Purge








































Reviews: