www.gecurrent.com
© 2021 Current Lighting Solutions, LLC. All rights reserved. GE and the GE monogram are trademarks of the
General Electric Company and are used under license. Information provided is subject to change without
notice. All values are design or typical values when measured under laboratory conditions.
ARCH018 (Rev 04/02/2021)
Lumination
®
(Tetra
®
Contour - Series)
Installation Guide
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
CAN ICES-005 (A) / NMB-005 (A)
Note:
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
Troubleshooting
Symptom
Condition
Solution
All LEDs are OFF
No AC input
Attach AC input and/or check circuit breaker
Incorrect wire attachment
Check wire connection(s) at the Tetra Contour LED light engine and power supply for im-
proper connections or short circuits. Make sure you have positive to positive and negative
to negative wire connections.
Some LEDs
appear dim
Overload (maximum load
exceeded)
Ensure the overall length of Tetra Contour LED light engine does not exceed the maximum
load as detailed in the
Tetra
®
Power Supply Installation Instructions.
Maximum recommended supply
wire length exceeded
Reduce the length of supply wire equal to or below the recommended maximum.
Mixed Suffix Codes of LED light
engine within an application
Make sure that all LED light engines have the same Suffix Code
(Suffix Code is located on each packaging label).
Some of the sections
are not illuminated
Incorrect wire attachment
Check the wire connections at the Tetra Contour LED light engine for improper connec-
tions. Make sure you have positive to positive and negative to negative wire connections.
Check for improper cutting resolution locations (see Item 21 on Page 2).
Light/dark banding
along a section
LED light engine stretched
during installation
Remove LED light engine and properly install.
Inspect and replace light engine if the silicone is damaged.
Loading Chart
LED Driver
Minimum Loading
Maximum Loading
White Colors
Maximum Loading
RGB Colors
79045 (GE080/MV/D24T1-A)
8 in. (0.20m)
22 ft. (6.69m)
50 ft. (15.24m)
67825 (GEPS24-100UGL-IP)
8 in. (0.20m)
27 ft. (8.19m)
59 ft. (17.98m)
62189 (GE180/MV/V24T1-C)
8 in. (0.20m)
25 ft. (7.59m) per Bank/
50 ft. (15.18m) per Driver
55 ft. (16.76m) per Bank/
110 ft. (33.53m) per Driver
Remote Mounting Distance
LED Driver
18 AWG (0.82mm
2
)
Supply Wire
16 AWG (1.31mm
2
)
Supply Wire
14 AWG (2.08mm
2
)
Supply Wire
12 AWG (3.31mm
2
)
Supply Wire
79045 (GE080/MV/D24T1-A)
1-20 ft. (0.3-6.1m)
30 ft. (0.3-9.1m)
50 ft. (0.3-15.2m)
86 ft. (0.3-26.1m)
67825 (GEPS24-100UGL-IP)
62189 (GE180/MV/V24T1-C)
