background image

14 Piping installation

Installation and operation manual

22

RWEYQ8~14T9Y1B

VRV IV water-cooled system air conditioner

4P452190-1D – 2020.10

▪ Install the joints horizontally, so that the caution label (a) attached

to the joint comes to the top.

▪ Do not tilt the joint more than 7.5° (see view A).

▪ Do not install the joint vertically (see view B).

a

a

A

B

7.5°
7.5°

a

Caution label

X

Not allowed

O

Allowed

▪ Make sure that the total length of the piping connected to the joint

is absolute straight for more than 500 mm. Only if a straight field
piping of more than 120 mm is connected, more than 500 mm of
straight section can be ensured.

>120 mm

>500 mm

14.3.4

To connect the refrigerant branching kit

For installation of the refrigerant branching kit, refer to the installation
manual delivered with the kit.

▪ Mount  the  refnet  joint  so  that  it  branches  either  horizontally  or

vertically.

▪ Mount the refnet header so that it branches horizontally.

A

B

±

3

a

b

c

a

a

Horizontal surface

b

Refnet joint mounted vertically

c

Refnet joint mounted horizontally

14.3.5

To protect against contamination

Seal  the  piping  and  wiring  intake  holes  using  sealing  material  (field
supply),  otherwise  the  capacity  of  the  unit  will  drop  and  small
animals may enter the machine.

14.3.6

Using the stop valve and service port

To handle the stop valve

Take the following guidelines into account:

▪ Make  sure  to  keep  the  appropriate  stop  valves  open  during

operation.  In  case  of  heat  pump  system,  the  gas  suction  stop
valve remains in the closed position.

▪ The gas and liquid stop valves are factory closed.

▪ Do  NOT  apply  excessive  force  to  the  stop  valve.  Doing  so  may

break the valve body.

To open the stop valve

1

Remove the stop valve cover.

2

Insert  a  hexagon  wrench  into  the  stop  valve  and  turn  the  stop
valve counterclockwise.

3

When the stop valve cannot be turned any further, stop turning.

4

Install the stop valve cover.

Result: 

The valve is now open.

To  fully  open  the  Ø19.1~Ø25.4  mm  stop  valve,  turn  the  hexagonal
wrench until a torque between 27 and 33 N•m is achieved.

Inadequate torque may cause leakage of refrigerant and breakage of
the stop valve cap.

To close the stop valve

1

Remove the stop valve cover.

2

Insert  a  hexagon  wrench  into  the  stop  valve  and  turn  the  stop
valve clockwise.

3

When the stop valve cannot be turned any further, stop turning.

4

Install the stop valve cover.

Result: 

The valve is now closed.

To handle the stop valve cover

▪ The  stop  valve  cover  is  sealed  where  indicated  by  the  arrow.  Do

NOT damage it.

▪ After  handling  the  stop  valve,  tighten  the  stop  valve  cover

securely,  and  check  for  refrigerant  leaks.  For  the  tightening
torque, refer to the table below.

Summary of Contents for VRV IV RWEYQ-T9









































Reviews: