![background image](http://html.mh-extra.com/html/daikin/vrv-iii/vrv-iii_service-manual_502207088.webp)
SiUS34-801A_b
Test Operation
VRVIII R-410A Heat Pump 60Hz
73
10.2 Procedure and Outline
Use the following procedure to conduct the initial test operation after installation:
10.2.1 Check Work Prior to Turn Power Supply On
Check on refrigerant piping /
ins
u
lation materials
Check airtight test and
v
ac
uu
m
drying.
Terminal
Dryer
(1000
W
)
Check the
b
elo
w
items.
2
Po
w
er
w
iring
2
Control transmission
w
iring
b
et
w
een
u
nits
2
Gro
u
nd
w
ire
Is the
w
iring installed as specified?
Is designated
w
iring
u
sed?
Is the
w
iring scre
w
tight?
Is the gro
u
nding
w
ork completed?
Is the ins
u
lation of the main po
w
er s
u
pply circ
u
it deteriorated?
Use a 500
V
megger tester to meas
u
re the ins
u
lation. (*1)
2
Do not
u
se a megger tester for other circ
u
its than 200
V
(or
240
V
) circ
u
it.
*1:Meas
u
res to
b
e taken against decreased ins
u
lation resistance in
the compressor:
If the compressor is left to stand for
an extended period of time after the
refrigerant is charged
w
ith the stop
v
al
v
e open and the po
w
er s
u
pply
OFF, refrigerant may
b
e mixed in the
compressor, th
u
s decreasing the
ins
u
lation resistance.
Heat the compressor as sho
w
n on
the right and then recheck the
ins
u
lation.
Is the pipe size correct?
Are the design press
u
res for the li
qu
id pipe, gas pipe, and
press
u
re e
qu
alizer pipe (in case of m
u
lti
u
nits) all not less than
5
8
0psi?
Is the pipe ins
u
lation material installed sec
u
rely?
Li
qu
id, gas pipe need to
b
e ins
u
lated. (Other
w
ise ca
u
ses
w
ater
leaks.)
Ha
v
e the airtight test and the
v
ac
uu
m drying
b
een cond
u
cted
according to the proced
u
re in the Installation Man
u
al?
Summary of Contents for VRV III
