background image

Installation manual

13

RZQ71~125B7V3B

Split System air conditioners

4PW16864-1A

W

IRING

 

DIAGRAM

A1P ........................... Printed circuit board

A2P ........................... Printed circuit board (INV)

BS1 ........................... Push button switch (forced defrosting/pump

down)

C1~C3R .................... Capacitor

DS1 ........................... Dip switch

E1HC......................... Crankcase heater

F1U ........................... Fuse (250 V, 10 A)

HAP (A1P)................. Service monitor (green)

HAP (A2P)................. Service monitor (green)

H1P (A1P) ................. Service monitor (red)

K1M•K2M .................. Magnetic relay

K1R ........................... Magnetic relay (Y15)

K2R ........................... Magnetic relay

K4R ........................... Magnetic relay (E1HC)

L1R............................ Reactor

M1C........................... Motor (compressor)

M1F•M2F................... Motor (fan)

PS ............................. Power circuit

R1•R2........................ Resistor

R1T............................ Thermistor (air)

R2T............................ Thermistor (coil)

R3T............................ Thermistor (discharge pipe)

R4T............................ Thermistor (suction pipe)

R5T............................ Thermistor (power module)

RC ............................. Signal receiver circuit

S1NPL ....................... Pressure sensor (low)

S1PH ......................... Pressure switch (high)

TC.............................. Signal transmission circuit

V1R ........................... Power module

V2R•V3R ................... Diode module

V1T ............................ Insulated gate bipolar transistor

X6A, X7A ................... Connector (option)

X1M ........................... Terminal strip

Y1E............................ Expansion valve

Y1S............................ 4 way valve

Y2S............................ Solenoid valve

Z1C............................ Noise filter

Z1F ............................ Noise filter (with surge absorber)

: Wire clamp

BLK

: Black

: Terminal

GRN

: Green

: Connector

BRN

: Brown

: Relay connector

BLU

: Blue

: Field wiring

ORG

: Orange

RED

: Red

WHT

: White

YLW

: Yellow

: Refer to the service manual for connecting wiring to

X6A.

: The position of the selector switches (DS1) indicate

the factory setting. For details, refer to the service
manual.

Summary of Contents for RZQ71B7V3B



















Reviews: