manualshive.com logo in svg
background image

CONTENTS

GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

SAFETY CONSIDERATIONS . . . . . . . . . . . . . . . . . . . . . 4

AGENCY APPROVALS  . . . . . . . . . . . . . . . . . . . . . . . . . 4

INSPECTION   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

INSTALLATION  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

MAINTENANCE  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

See the following page for a complete Table of Contents.

NOTES, CAUTIONS AND WARNINGS

The installer should pay particular attention to the words:
NOTECAUTION, and WARNING. Notes are intended to
clarify or make the installation easier. Cautions are given
to prevent equipment damage. Warnings are given to
alert installer that personal injury and/or equipment dam-
age may result if installation procedure is not handled
properly.

INSTALLATION 
MANUAL

CAUTION:

READ ALL SAFETY GUIDES BEFORE YOU 
BEGIN TO INSTALL YOUR UNIT.

SAVE THIS MANUAL

208/230/460
VOLT ONLY

208/230/460
VOLT ONLY

SPLIT-SYSTEM

CONDENSING UNITS

(AIR COOLED)

MODEL:  HA090

035-18204-001-B-0703

 

Содержание HA090





















Отзывы: