Daikin RZAG100M7Y1B Installation Manual Download Page 5

Table of contents

Installation manual

5

RZAG71~Y1
Sky Air Alpha-series
4P485927-1 – 2017.04

Table of contents

1 About the documentation

5

1.1

About this document..................................................................

5

2 About the box

5

2.1

Outdoor unit...............................................................................

5

2.1.1

To remove the accessories from the outdoor unit.......

5

3 Preparation

6

3.1

Preparing installation site ..........................................................

6

3.1.1

Installation site requirements of the outdoor unit ........

6

4 Installation

6

4.1

Mounting the outdoor unit..........................................................

6

4.1.1

To provide the installation structure ............................

6

4.1.2

To install the outdoor unit............................................

6

4.1.3

To provide drainage ....................................................

6

4.1.4

To prevent the outdoor unit from falling over ..............

7

4.2

Connecting the refrigerant piping ..............................................

7

4.2.1

To connect the refrigerant piping to the outdoor unit ..

7

4.3

Checking the refrigerant piping .................................................

8

4.3.1

Checking refrigerant piping: Setup..............................

8

4.3.2

To check for leaks.......................................................

8

4.3.3

To perform vacuum drying ..........................................

8

4.4

Charging refrigerant ..................................................................

8

4.4.1

About charging refrigerant ..........................................

8

4.4.2

About the refrigerant ...................................................

9

4.4.3

To determine the additional refrigerant amount .......... 10

4.4.4

To determine the complete recharge amount ............. 10

4.4.5

Charging refrigerant: Setup......................................... 11

4.4.6

To charge additional refrigerant .................................. 11

4.4.7

To activate/deactivate the vacuum mode field setting

11

4.4.8

To completely recharge refrigerant ............................. 11

4.4.9

To fix the fluorinated greenhouse gases label ............ 11

4.5

Connecting the electrical wiring.................................................

12

4.5.1

About electrical compliance ........................................ 12

4.5.2

Guidelines when connecting the electrical wiring ....... 12

4.5.3

Specifications of standard wiring components............ 12

4.5.4

To connect the electrical wiring on the outdoor unit.... 12

4.6

Finishing the outdoor unit installation ........................................

13

4.6.1

To finish the outdoor unit installation .......................... 13

4.6.2

To check the insulation resistance of the compressor

14

5 Commissioning

14

5.1

Checklist before commissioning ................................................

14

5.2

To perform a test run .................................................................

14

5.3

Error codes when performing a test run ....................................

15

6 Disposal

15

7 Technical data

16

7.1

Overview: Technical data ..........................................................

16

7.2

Service space: Outdoor unit ......................................................

16

7.3

Piping diagram: Outdoor unit.....................................................

17

7.4

Wiring diagram: Outdoor unit ....................................................

17

1

About the documentation

1.1

About this document

Target audience

Authorised installers

INFORMATION

This appliance is intended to be used by expert or trained
users  in  shops,  in  light  industry  and  on  farms,  or  for
commercial use by lay persons.

Documentation set

This  document  is  part  of  a  documentation  set.  The  complete  set
consists of:

General safety precautions:

▪ Safety instructions that you must read before installing

▪ Format: Paper (in the box of the outdoor unit)

Outdoor unit installation manual:

▪ Installation instructions

▪ Format: Paper (in the box of the outdoor unit)

Installer reference guide:

▪ Preparation of the installation, reference data,…

▪ Format:  Digital  files  on 

http://www.daikineurope.com/support-

and-manuals/product-information/

Latest revisions of the supplied documentation may be available on
the regional Daikin website or via your dealer.

The original documentation is written in English. All other languages
are translations.

Technical engineering data

▪ A 

subset

  of  the  latest  technical  data  is  available  on  the  regional

Daikin website (publicly accessible).

▪ The 

full  set

  of  latest  technical  data  is  available  on  the  Daikin

extranet (authentication required).

2

About the box

2.1

Outdoor unit

2.1.1

To remove the accessories from the
outdoor unit

ENERG

IJA

Y

IA

IE

ENERG

IJA

Y

IA

IE

2

3

1

a

b

c

d

e

a

General safety precautions

b

Outdoor unit installation manual

c

Cable tie

d

Fluorinated greenhouse gases label

e

Energy label

Summary of Contents for RZAG100M7Y1B





















Reviews: