Daikin RRDQ220V1 Operation Manual Download Page 23

Page: 23 / 28

RRDQ220V1

BEFORE REQUESTING REPAIR OR SERVICES

Symptom

Cause

Solution

The high

pressure switch

does not work.

① The high pressure switch is out of

order.

① Repair.

② Faston terminals are disconnected.

② Connect the faston terminals properly.

The high pressure

switch works even

at low pressure.

① The high pressure switch is out of

order.

① Repair.

The low pressure

switch does not

work.

① Auto/Manual Shut-off Mode Setting

sets at "Manual" side.

① Switch the shut-off mode setting to

"Auto Shut-off".

② The low pressure switch is out of

order.

② Repair.

The purity of

the recycled

refrigerants is not

good enough.

① Molecular Sieve is contaminated.

① Replace Molecular Sieve Replacement

Kit (AR338) referring to page 17 and

Filter (TF011).

② The O-ring in Dry Filter Housing is

damaged.

② Replace Molecular Sieve Replacement

Kit (AR338) referring to page 17.

Refrigerants leak

from the unit.

① The charging hose and the hose

gasket are not in good condition.

① Replace the charging hose and gasket.

② The lid of Dry Filter Housing is loose.

② Close the lid tight.

③ Filter and Sight Glass are loose.

③ Tighten Filter and Sight Glass.

④ The valve of Oil Discharge Port is

open.

④ Close the valve and put a cap on the

port.

BEFORE REQUESTING

REPAIR OR SERVICES

Summary of Contents for RRDQ220V1




























Search results

Summary of Contents for RRDQ220V1

Reviews:

Brands by name

Popular brands

Daikin RRDQ220V1, Operation Manual

Search results

Summary of Contents for RRDQ220V1

Reviews:

Brands by name

Popular brands