Daikin RRDQ220V1 Operation Manual Download Page 15

Page: 15 / 28

RRDQ220V1

① Setting up as the above drawing.

② Turn Switching Valve (V2) to [PURGE] position.

＊ Do not turn the valve during operation or Discharge Pressure Gauge may be damaged.

③ Set Auto Shut-off/Manual Mode Setting to [Auto Shut-off] position.

＊ When using the Auto Shut-off mode, the unit does not starts when Suction Pressure is lower than

atmospheric pressure.

④ Set Power Switch to [ON] position.
　 Push Start Switch once.

⑤ Turn Suction Valve (V1) slowly to [PURGE] position adjusting Suction Pressure to less than

0.2MPa.

⑥ Close the liquid port of the cylinder when the unit stops automatically.

⑦ Turn Discharge Valve (V3) to [CLOSE] position and close the discharge hose ball valve.

⑧ Set Power Switch to [OFF] position.

⑨ Disconnect the hoses.

＊ Vapor refrigerant remains in the recycle unit and the hose of the discharge side.

Connect the hose of the discharge side to an evacuated cylinder to recover all refrigerant in the
recycle unit and the hose.

4）Refrigerant Discharge (Purge) Procedure

Operation time

Suction

Discharge

rs.
of

MED

RESOLUTION

Cy Scale

OPEN

Liquid valve

Vapor valve

Cylinder

Manifold

Ball valve

OPEN

Ball valve

Suction Valve

PURGE

Switching Valve

OPEN

Discharge Valve

Low

pressure side

High

pressure side

0.2MPa

PURGE

OFF

Power

O N

Start

OFF

Power

O N

OFF

RRDQ220V1

Vapor valve

Liquid valve

Auto Shut-oﬀ

Auto

Shut-off

Manual

◆ Use safety glasses and leather hand gloves when operating or disconnecting hoses.
If refrigerant gas touches your skin or gets into your eyes, it may cause frostbite or damage your eye

sight.

CAUTION

◆ Adjust Suction Pressure less than 0.2MPa in purging.
Otherwise, it may cause damage on the compressor.

CAUTION

A scale must be used to prevent
overfilling of cylinder.

HOW TO USE

Summary of Contents for RRDQ220V1




























Search results

Summary of Contents for RRDQ220V1

Reviews:

Brands by name

Popular brands

Daikin RRDQ220V1, Operation Manual

Search results

Summary of Contents for RRDQ220V1

Reviews:

Brands by name

Popular brands