Operating instructions
34
Daikin RoCon HP
Daikin Control
008.1420844 – 05/2014
5
x
Parameter settings
5.2.2 Level "System Configuration"
Parameter
Description
Access
Setting range
Min / Max
Factory
setting
Increment
BE
HF
Power DHW
Heating output of electric auxiliary heater for hot water generation
N
E
1000 -
40000 W
3000 W
1000 W
BUH s1 power
Heat capacity of the ancillary electric heater in Stage 1 heating support
N
E
1000 -
40000 W
3000 W
1000 W
BUH s2 power
Heat capacity of the ancillary electric heater in Stage 2 heating support
N
E
1000 -
40000 W
3000 W
1000 W
Power BIV
Setting limits the output of the heating support.
N
E
3000 -
40000 W
15000 W
1000 W
TDiff-DHW CH Sup-
port
Only when parameter [HZU] = On.
Heating support activated when
Tdhw > T
HZUmin
+ 4 K
and
Tdhw > [T-HS Setpoint] + 1 K.
Heating support deactivated when
Tdhw < T
HZUmin
or
Tdhw < [T-HS Setpoint].
T
HZUmin
= Current active target hot water temperature [T-DHW Setpoint] + set parameter val-
ue [TDiff-DHW CH Support].
Tdhw = Current hot water storage tank temperature
[T-HS Setpoint] = current active inflow target temperature (see tab. 5-12 and chapter 3.6.4)
N
E
2 - 15
5
1
T vbh1 max
Setting limits the inflow temperature (measured at t
V, BH
) with active heating support function.
N
E
5 - 60 °C
60 °C
1 °C
Equilibrium Temp
Setting affects the operation of the potential-free AUX switching contact (toggle switch output
A) Defined in the parameter [AUX Fct].
Only when parameter [Equilibrium Func.] = On.
Outdoor temperature from which the optional ancillary heating is activated for supporting the
room heating. The bivalent temperature is relevant for operation of the optional ancillary heat-
er based on a backup demand (room heating operation). The temperature of the sensor inte-
grated into the external unit for heat pump (info value TA2) is used.
The info value TA2 displayed can differ from the value in the standard display depending on
parameter [Outside Config].
E
E
-15 °C to
+35 °C
0 °C
1 °C
Quite Mode
Mode for low-noise operation with reduced output (see chapter 3.4.10).
0: Deactivated
1: Activated
2: Operated in whisper mode only at night between 22:00 and 6:00 hours.
E
E
0 - 2
0
-
AUX Fct
Setting assigns the switching conditions to the potential-free AUX contact (toggle switch out-
put A; see chapter 3.6.9).
0: Function deactivated
AUX switching contact changes;
1: When storage tank temperature (Tdhw)
≥
value of parameter [T-DHW 1 min].
2: When there is a cooling or heating demand.
3: When there is a hot water demand to the heat pump or the configured backup heater is re-
quired for heating support.
4: When there is a malfunction.
5: When sensor value (TVBH) > 60 °C.
6: When the outdoor temperature < parameter value [Equilibrium Temp].
→
Heat pump continues to operate = Parallel bivalence operation.
7: When the outdoor temperature < parameter value [Equilibrium Temp] + there is a heating
or hot water demand.
→
Heat pump does not continue to operate = Alternative bivalence operation.
8: When there is a hot water demand.
9: When outside temperature < parameter [Equilibrium Temp] + heat demand "Room heating"
(not for hot water demand). Heat pump no longer operates in room heating mode below the
value set in parameter [Equilibrium Temp] - only in hot water mode.
N
E
0 - 9
0
1
AUX time
AUX switching contact (A) switches with a delay when the switching condition (see parameter
[AUX Fct]) is pending for longer than the set time.
N
E
0 - 600 s
120 s
5 s
T-DHW 1 min
Switching threshold storage tank temperature (Tdhw) for AUX switching contact (see param-
eter [AUX Fct]).
N
E
20 - 85 °C
50 °C
1 °C
Delta-T CH
Set outdoor temperature spread The Daikin Altherma EHS(X/H) heating circulation pump con-
trols the flow rate in order to achieve the set spread between the inflow target temperature and
the return flow temperature (t
V, BH
- t
R1
).
N
E
2 - 20 K
7 K
1 K
V var
Current minimum necessary volume flow in the system (calculated value, not configurable)
N
S
INFO VALUE
XXX
-
T-Flow CH adj
Only if parameter [Interlink fct] = On:
With a closed cooling RT switching contact
, the inflow target temperature is increased by
the set value (see tab. 5-1, parameter [Interlink fct]). Demand, e.g. from FWXV(15/20)AVEB.
N
E
0 - 50 °C
5 °C
1 °C
T-Flow Cooling adj
Only if parameter [Interlink fct] = On:
With a closed cooling RT switching contact
, the cooling inflow target temperature is re-
duced by the set value (see tab. 5-1, parameter [Interlink fct]). Demand, e.g. from
FWXV(15/20)AVEB.
N
E
0 - 50 °C
5 °C
1 °C
Min Pressure
Defines the minimum water pressure.
Pressure monitor function (only if the pressure sensor is activated, [Pressure Config] = On,
see tab. 5-1): If the measured value falls below the set value, the Daikin Altherma EHS(X/H)
is switched off and an error message is generated.
N
E
0.1 - 5.0 bar
0.5 bar
0.1 bar
Max Pressure
Defines the maximum water pressure.
Pressure monitor function (only if the pressure sensor is activated, [Pressure Config] = On,
see tab. 5-1): If the measured value exceeds the set value, a warning message is generated.
N
E
0.1 - 5.0 bar
3.0 bar
0.1 bar
Set Point Pressure
Defines the set water pressure.
Pressure monitor function (only if the pressure sensor is activated, [Pressure Config] = On,
see tab. 5-1): If the measured value falls below the value set in the [Max Pressuredrop] pa-
rameter by more than the set amount, a warning message is generated.
N
E
0.1 - 5.0 bar
0.9 bar
0.1 bar
