background image

17

3P477778-7G English

•  If the piping length between the outdoor units exceeds 6.5 ft. (2 m), 

create a rise of 8 in. (200 mm) or more in the suction gas and high/
low pressure gas line within a length of 6.5 ft. (2 m) from the kit. 

If ≤6.5 ft. (2 m)

1

2

a

If >6.5 ft. (2 m)

1

a

b

c

2

1  To indoor units
2  Piping between outdoor units
a  

≤6.5 ft. (2 m)

b  

≥8 in. (200 mm)

c  >6.5 ft. (2 m)

 NOTE

There are restrictions on the refrigerant pipe connection order be-
tween outdoor units during installation in case of a multiple outdoor 
unit system. Install according to following restrictions. The capacities 

of outdoor units A and B must fulfill the following restriction conditions: 
A≥B.

A

B

1 2

1  To indoor units
2  Outdoor unit multi connection 

piping kit (first branch)

8 .2 .6 .  Branching the refrigerant piping

For installation of the refrigerant branch kit, refer to the installation 
manual delivered with the kit.

A

B

±3

1

1

Horizontal

Vertical

1 Horizontal surface

•  Mount the REFNET joint so that it branches either horizontally or 

vertically.

•  Mount the REFNET header so that it branches horizontally.

Installation of the multi connection piping kit.

A

1

B

1

C

D

±15°

C >4-3/4 in. (120 mm)
D >19-11/16 in. (500 mm)

• 

Install the joints horizontally, so that the caution label (1) attached to 
the joint comes to the top.

 

- Do not tilt the joint more than 15° (see view A).

 

- Do not install the joint vertically (see view B).

• 

Make sure that the total length of the piping connected to the joint 
is absolute straight for more than 19-11/16 in. (500 mm). Only if a 

straight field piping of more than 4-3/4 in. (120 mm) is connected, 

more than 19-11/16 in. (500 mm) of straight section can be ensured.

• 

Improper installation may lead to malfunction of the outdoor unit.

8 .3 .  Guidelines for handling stop valve

8 .3 .1 .  Cautions on handling the stop valve

• 

Make sure to keep all stop valves open during operation. 

•  The figure below shows the name of each part required in handling 

the stop valve.

• 

The stop valves are factory closed.

• 

When handle the stop valves, be careful not to damage the port 
pipes around (refer to P22). 

3

4

1

2

1 Service port and service port 

cover

2 Stop valve
3 Field piping connection
4 Stop valve cover

1

2

3

4

5

1 Service port
2 Cap
3

Hexagon hole

4 Shaft
5 Seal

01_EN_3P477778-7G.indb   17

1/15/2019   10:58:09

Summary of Contents for REYQ120XATJU


















































Reviews: