manualshive.com logo in svg

Daikin HXY080A7V1B, Installation And Operation Manual

Share
Download
Daikin HXY080A7V1B Installation And Operation Manual Download Page 17

125A7V1B

VRV IV System indoor unit

4P325971-1B – 2012.07

Installation and operation manual

15

a Low voltage cable bundle (see 

"6.3.2. Overview of 

electrical connections on the indoor unit" on 

page 11

b High voltage cable bundle (see 

"6.3.2. Overview of 

electrical connections on the indoor unit" on 

page 11

c Earth connection

d Optional

3 

Fix the cable with cable ties to the cable tie mountings to ensure
strain relief and to make sure that it does NOT come in contact
with the piping and sharp edges.

7.3.6.

To connect the user interface

The unit is equipped with a user interface offering a user-friendly way
to set up, use and maintain the unit.

Before operating the user interface, follow this installation procedure.

Procedure

Remove the front part of the user interface

Insert a slotted screwdriver into the slots (1)
in the rear part of the user interface, and
remove the front part of the user interface.

Fixation of the user interface to the indoor unit

1 

Fix the wallplate of the user interface to the frontplate of the unit.
For installation of the frontplate, see 

"7.4.1. To fix the user

interface cover to the indoor unit" on page 16

.

2 

Cut off a 2 wire conductor.

3 

Connect the wires to the user interface as shown below.

From the rear

4 

Reinstall the faceplate onto the wallplate.
First begin fitting from the clips at the bottom.

5 

Remove the user interface cover from its hinge.

CAUTION

Do NOT push or place redundant cable length in the unit.

NOTICE

The wiring for connection is not included.

NOTICE

The user interface, delivered in a kit, has to be mounted
indoors.

NOTICE

The PCB is mounted in the faceplate of the user interface.

Be careful NOT to damage it.

INFORMATION

For connection to the switchbox see 

"7.3.5. To connect the

electrical wiring on the indoor unit" on page 14

.

X2M

X1M

X801M

A4P

b

a

c

d

1

NOTICE

Be careful NOT to distort the shape of the backside of the
user interface by overtightening the mounting screws..

a

b

P

1

P

2

a

Rear part of the user interface

b

Front part of the user interface

1

2

1

Summary of Contents for HXY080A7V1B

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands