Daikin FXSQ05TAVJU, Engineering Data

Page: 70 / 76

Installation Manual EDUS391777-F17
15 FXSQ-TAVJU
3P184443-13Z
15 English
WARNING
r
When wiring, form the wirings orderly so that the control
DQZNKFECPDGUGEWTGN[HHVJGEQPVTQNDQZNKFKUPQV
in place, the wirings may come out or be sandwiched by the
DQZCPFVJGNKFCPFECWUGGNGEVTKEUJQEMUQTCƂTG
(1) Remove the control box lid.
Screws
(2 points)
Fig. 23
(2) Attach the conduit to the conduit mounting plate (12).
Conduit mounting
plate (12)
Conduit
ƂGNFUWRRN[
Lock nut
ƂGNFUWRRN[
Fig. 24-1
r Attach the wire sealing material (small) (10) to the con-
duit, the power supply wiring and the ground wiring.
Conduit mounting
plate (12)
Conduit
mounting
plate (12)
Conduit
ƂNGFUWRRN[
9KTGUGCNKPIOCVGTKCNUOCNN
2QYGTUWRRN[
wiring and ground
wiring
8KGYGFHTQOVJGUKFG
Fig. 24-2
r Loosen the screws (2 points) in part A.
Screws
(2 points)
B
A
9KTKPIƂZVWTG
Fig. 24-3
r Insert the hook part of the conduit mounting plate (12)
into part B and secure the conduit mounting plate (12)
with the screws loosened (2 points).
NOTE
1. 4GOQXGVJGYKTKPIƂZVWTGKH[QWJCXGFKHƂEWNV[KP
performing this step.
Screws
(2 points)
Conduit mounting
plate (12)
Hook
Fig. 24-4
(3) Connect the wiring into the control box through the
wiring intake beside the control box.
Remote controller
wiring
Transmission
wiring
Wiring intake
(low voltage)
Wiring intake
(high voltage)
Power supply
wiring and
ground wiring
Fig. 25
(4) Follow the instructions below and perform wiring in
the control box.
F2
T2 P1 P2 F1 T1
5GEWTGN[ƂZVJGYKTKPIVQ
VJGRTQXKFGFYKTKPIƂZVWTG
YKVJVJGENCOR
6GTOKPCNDNQEM:/
HQTRQYGTUWRRN[YKTKPI
CPFITQWPFYKTKPI
%QPPGEVVJGYKTKPI
VJTQWIJVJGEQPVTQNDQZ
WRVQVJGUJGCVJGFRCTV
2QYGTUWRRN[YKTKPI
JKIJXQNVCIG
)TQWPFYKTKPIJKIJXQNVCIG
4GOQVGEQPVTQNNGTYKTKPI
NQYXQNVCIG
6GTOKPCNDNQEM:/HQTTGOQVGEQPVTQNNGTYKTKPI
CPFVTCPUOKUUKQPYKTKPI
4GOQVGEQPVTQNNGTYKTKPI
0QRQNCTKV[
6TCPUOKUUKQPYKTKPI
0QRQNCTKV[
4GOQVGEQPVTQNNGTYKTKPIOGVJQF
Never connect the
power supply wiring.
Prohibited
%QPPGEVKQPOGVJQF
HQTRQYGTUWRRN[YKTKPI
CPFITQWPFYKTKPI
:
1
/
L1
L2
Fig. 26
NOTE
1. Secure the wiring between the wiring intake and conduit
with the clamp (8) so that the wiring will not become loose.