Daikin FXSQ05TAVJU, Engineering Data

Page: 63 / 76

EDUS391777-F17 Installation Manual
FXSQ-TAVJU 8
3P184443-13Z
8 English
6. REFRIGERANT PIPING WORK
r For the outdoor unit refrigerant piping, refer to the installa-
tion manual attached to the outdoor unit.
r
Carry out insulation of both gas and liquid refrigerant piping
securely. If not insulated, it may cause water leakage. For
gas piping, use insulation material of which heat resistant
temperature is not less than 250°F (120°C).
For use under high humidity, strengthen the insulation ma-
terial for refrigerant piping. If not strengthened, the surface
of insulation material may sweat.
r
Before installation work, make sure that the refrigerant is
R410A. (Unless the refrigerant is R410A, the nor mal opera-
VKQPECPPQVDGGZRGEVGF
CAUTION
This air conditioner is a dedicated model for refriger-
ant R410A. Make sure to meet the require ments shown
below and carry out installation work.
r 7UGFGFKECVGFRKRKPIEWVVGTUCPFƃCTKPIVQQNUHQT
R410A.
r 9JGPOCMKPICƃCTGEQPPGEVKQPEQCVVJGƃCTGFKP -
ner surface only with ether oil or ester oil.
r 7UGQPN[VJGƃCTGPWVUCVVCEJGFVQVJGCKTEQPFKVKQP
-
GT+HQVJGTƃCTGPWVUCTGWUGFKVOC[ECWUGTGHTKIGT
-
ant leakage.
r To prevent contamination or moisture from getting
into the piping, take measures such as pinch ing or
taping the pipings.
&QPQVOKZUWDUVCPEGQVJGTVJCPVJGURGEKƂGFTGHTKI
-
erant such as air into the refrigeration circuit.
If the refrigerant leaks during the work, ventilate the
room.
r The refrigerant is pre-charged in the outdoor unit.
r When connecting the pipings to the air conditioner,
make sure to use a spanner and a torque wrench as
shown in
Fig. 9 .
r (QTVJGFKOGPUKQPQHƃCTGFRCTVCPFVJGVKIJVGPKPI
torque, refer to the Table 2.
r 9JGPOCMKPICƃCTGEQPPGEVKQPEQCVVJGƃCTGFKPPGT
surface only with ether oil or ester oil.
(Refer to Fig. 10)
6JGPVWTPVJGƃCTGPWVVQVKOGUYKVJ[QWTJCPFCPF
screw in the nut.
Torque wrench
Spanner
Flare nut
Union joint
Fig. 9
%QCVVJGƃCTGFKPPGTUWTHCEG
QPN[YKVJGVJGTQKNQTGUVGTQKN
Fig. 10
Table 2
Piping
size
[in. (mm)]
Tightening
torque
[lbf·ft. (N·m)]
Dimension for
RTQEGUUKPIƃCTG
A [in. (mm)]
Flare shape
[in. (mm)]
I 1/4
(6.4)
10.4–12.7
(15.7±1.5)
0.342–0.358
(8.9±0.2)
90°±2°
A
45°±2°
R0.016-0.031
(0.4-0.8)
I
3/8
(9.5)
24.1–29.4
(36.3±3.6)
0.504–0.520
(13.0±0.2)
I 1/2
(12.7)
36.5–44.5
(54.9±5.4)
0.638–0.654
(16.4±0.2)
I 5/8
(15.9)
45.6–55.6
(68.6±6.8)
0.760–0.776
(19.5±0.2)
CAUTION
&QPQVJCXGQKNCFJGTGVQVJGUETGYƂZKPIRCTVQHTGUKP
parts.
If oil adheres, it may weaken the strength of screwed part.
&QPQVVKIJVGPƃCTGPWVUVQQVKIJV
+HCƃCTGPWVETCEMUVJGTGHTKIGTCPVOC[NGCM
r
If there is no torque wrench, use Table 3 as a rule of
thumb.
9JGPVKIJVGPKPICƃCTGPWVYKVJCURCPPGTJCTFGTCPF
harder, there is a point where the tightening torque sud-
denly increases.
From that position, tighten the nut additionally at the
angle shown in Table 3.
#HVGTVJGYQTMKUƂPKUJGFEJGEMUGEWTGN[VJCVVJGTGKUPQ
gas leak.
If the nut is not tightened as instructed, it may cause
slow refrigerant leak and result in malfunction (such as
does not cool or heat).
Table 3
Piping size
[in. (mm)]
Tightening
angle
Recommended arm length of
tool used
I
1/4 (6.4) 60°–90°
#RRTQZKPOO
I 3/8 (9.5) 60°–90° #RRTQZKPOO
I 1/2 (12.7) 30°–60° #RRTQZKPOO
I 5/8 (15.9) 30°–60° #RRTQZKPOO
CAUTION
+PUWNCVKQPQHƂGNFRKRKPIOWUVDGECTTKGFQWVWRVQVJG
connection inside the casing.
+HVJGRKRKPIKUGZRQUGFVQVJGCVOQURJGTGKVOC[ECWUG
sweating, burn due to touching the piping, electric shocks
QTCƂTGFWGVQVJGYKTKPIVQWEJKPIVJGRKRKPI