background image

7 Maintenance and service

Installation and operation manual

11

FXHQ-A
VRV system air conditioner
3P668115-3E – 2022.11

1

Open  the  suction  grille

.  Simultaneously  slide  all  knobs  (2  for

class  32,  3  for  class  63  and  100)  in  the  direction  of  the  arrow
and carefully open the suction grille.

a

a

Knob

2

Remove the air filter.

 Push up the filter knobs at 2 places and

take out the air filter.

a

a

Filter knob

3

Clean the air filter.

 Use a vacuum cleaner or wash with water.

If  the  air  filter  is  very  dirty,  use  a  soft  brush  and  neutral
detergent.

4

Dry the air filter in the shadow.

5

Reattach the air filter and close the suction grille.

6

Turn ON the power.

7

To  remove  warning  screens,  see  the  reference  guide  of  the
user interface.

7.2.3

To clean the suction grille

1

Open  the  suction  grille

.  Simultaneously  slide  all  knobs  (2  for

class  32,  3  for  class  63  and  100)  in  the  direction  of  the  arrow
and carefully open the suction grille.

a

a

Knob

2

Remove  the  suction  grille.

  While  keeping  the  suction  grille

open, unhook the straps from the indoor unit. Then remove the
clips (2 for class 32, 3 for class 63 and 100) holding the suction
grille.

a

a

Strap

a

a

Clip

3

Remove  the  air  filter.

  Refer  to 

"7.2.2  To  clean  the  air

filter"

 [

4

 10].

4

Clean  the  suction  grille.

  Wash  with  a  soft  bristle  brush  and

water or neutral detergent. If the suction grille is very dirty, use
a  typical  kitchen  cleaner,  leave  it  on  for  10  min,  then  wash  it
with water.

5

Reattach  the  air  filter.

  Refer  to 

"7.2.2  To  clean  the  air

filter"

 [

4

 10].

6

Reattach  the  suction  grille  and  close  it.

  (steps  2  and  1  in

reverse order).

INFORMATION

When closing the suction grille, make sure the straps of the
suction grille are not pinched anywhere.

7.3

About the refrigerant

This  product  contains  fluorinated  greenhouse  gases.  Do  NOT  vent
gases into the atmosphere.

Refrigerant type: R410A

Global warming potential (GWP) value: 2087.5

NOTICE

Applicable  legislation  on 

fluorinated  greenhouse  gases

requires  that  the  refrigerant  charge  of  the  unit  is  indicated
both in weight and CO

2

 equivalent.

Formula  to  calculate  the  quantity  in  CO

2

  equivalent

tonnes:

  GWP  value  of  the  refrigerant  ×  total  refrigerant

charge [in kg]/1000

Contact your installer for more information.

WARNING

▪ The refrigerant in the system is safe and normally does

NOT  leak.  If  the  refrigerant  leaks  in  the  room,  contact
with a fire of a burner, a heater or a cooker may result
in a harmful gas.

▪ Turn  OFF  any  combustible  heating  devices,  ventilate

the room and contact the dealer where you purchased
the unit.

▪ Do NOT use the system until a service person confirms

that the portion where the refrigerant leaks is repaired.

Summary of Contents for FXHQ32AVEB8

























Reviews: