background image

15

8. WIRING EXAMPLE AND HOW TO SET THE REMOTE CONTROLLER

8-1 HOW TO CONNECT WIRINGS

Conduit for power supply wiring
Unscrew and remove the conduit mounting plate from the electric parts box. 

(Refer to Fig. 20)

Fix a conduit to the plate with a lock nut and reattach them at original position.

Power supply wiring and ground wiring
Unscrew and remove the service lid.
Thread the power supply wiring and ground wiring through the included insulating tube (short) (7) and 
secure them with the included clamp (small) (5). 

(Refer to Fig. 21)

Connect the power supply wiring and ground wiring to the power supply terminal block (3P).
When doing this, firmly secure using the included clamp (small) (5) according to the figure.

(Refer to Fig. 22)

Transmission wiring and remote controller wiring
Unscrew and remove the service lid.
Thread the remote controller wiring and transmission wiring through the included insulating tube (long) (7) 
and secure them with the included clamp (small) (5). 

(Refer to Fig. 21)

Connect the remote controller wiring and the transmission wiring to the terminal block (6P).
When doing this, tie the remote controller wiring and the transmission wiring using the included clamp (small) 
(5) and then firmly secure using the included clamp (small) (5) according to the figure. 

(Refer to Fig. 22)

Electric parts box 

Refrigerant piping 

Conduit

Lock nut

Conduit mounting plate

Screw 

Fig. 20

Insulating tube (short)
(accessory) (7)

Insulating tube (long)
(accessory) (7)

Clamp small
(accessory) (5)

Power
supply
wiring

Ground
wiring

Clamp small
(accessory) (5)

Tramsmission
wiring

Remote 
controller
wiring

Fig. 21

(1in.)

(1in.)

01_EN_3PN07521-1.fm  Page 15  Monday, June 19, 2006  5:05 PM

Summary of Contents for FXAQ07MVJU
























Reviews: