background image

27

English

NOTE

1.

Terminal numbers of outdoor and indoor units must be matched.

2-1.

Connect the remote controller only to the master unit.

2-2.

The remote controller needs to be wired only to the master unit; it does not need to be connected to the 
slave units through transition wiring. (Do not connect transition wiring to the slave units.)

2-3.

The indoor temperature sensor is effective only for indoor units to which the remote controller is con-
nected.

2-4.

The length of wiring between the indoor unit and the outdoor unit varies depending on the connected 
model, the number of connected units, and the maximum piping length.
For details, refer to the technical documents.

• Group control: 

1 remote controller controls up to 16 indoor units

(All indoor units operate according to the remote controller). 

(Refer to Fig. 42)

NOTE

Terminal numbers of outdoor and indoor units must be matched.

When implementing group control

When using as a pair unit or as a master unit for simultaneous multiple unit operation, you may carry out 
simultaneous start/stop (group) control up to 16 units with the remote controller. 

(Refer to Fig. 43)

In this case, all the indoor units in the group will operate in accordance with the group control remote con-
troller.

Select a remote controller which matches as many of the functions in the group as possible.

P1 P2

1 2 3

1 2 3

1 2 3

P1 P2

P1 P2

P1 P2

1 2 3

1 2 3

1 2 3

Power supply

220-240V

~

50Hz

Power supply

220-240V

~

50Hz

Power supply

220-240V

~

50Hz

Outdoor unit

Indoor unit

Outdoor unit

Indoor unit

Outdoor unit

NOTE)

NOTE)

NOTE)

Indoor unit

Group control remote controller 
(Optional accessories)

Group control

Earth leakage 
breaker

Earth leakage 
breaker

Earth leakage 
breaker

Fig. 42

Fig. 43

Indoor unit 
(Slave)

Outdoor unit 1

Outdoor unit 2

Outdoor unit 16

Indoor unit 1

Indoor unit 2 
(Master)

Group control remote controller

Indoor unit 16

For simultaneous 
operation type, be 
sure to perform the 
remote controller 
wiring through the 
master unit.

01_EN_3P177351-6P.fm  Page 27  Sunday, September 30, 2012  1:52 PM

Summary of Contents for FUQ71CVEB










































Reviews: