background image

9

Read Before Operation

Read Before Operation

 CAUTION

Incorrect handling of batteries can result in injury from battery leakage, rupturing or heating, or lead to equipment 
failure.

Please observe the following precautions and use safely.

•  If the alkaline solution from the batteries should get in the eyes, do not rub the eyes. Instead, immediately flush the eyes with tap water and 

seek the attention of a medical professional.

•  Keep batteries out of reach of children. In the event that batteries are swallowed, seek the immediate attention of a medical professional.
•  Do not expose batteries to heat or fire. Do not disassemble or modify batteries. The insulation or gas release vent inside the battery may be 

damaged, resulting in battery leakage, rupturing, or heating.

•  Do not damage or peel off labels on the batteries.

Remote 
controller holder

Remote controller

Screws

Position     and
    correctly!

+

2

3

1

NOTE

Notes on batteries

•  To avoid possible injury or damage from battery leakage or rupturing, remove the batteries when not using the product for long periods of 

time.

•  The standard replacement time is 1 year. Both batteries should be replaced at the same time. Be sure to replace them with new size AAA.

LR03 (alkaline) batteries.

•  When battery power has run out, the LCD will begin blinking as an alert that the batteries need replacing. In some cases, when battery 

consumption is accelerated owing usage conditions, signal reception may decline before the LCD begins blinking.

•  The batteries supplied with the remote controller are for initial operation. The batteries may run out in less than 1 year.

Note on remote controller

•  Do not drop the remote controller. Do not get it wet.

 

„

To insert the batteries

1. Slide the front cover to take it off.
2. Insert 2 dry batteries AAA.LR03 (alkaline).
3. Replace the front cover.

 

„

To fix the remote controller holder to a wall

1. Choose a place from where the signals reach the unit.
2.  Fix the holder to a wall, a pillar, or similar location with the screws supplied with 

the holder.

3. Place the remote controller in the remote controller holder.

 

„

Turn on the circuit breaker

• After the power is turned on, the flaps of the indoor unit open and close once to 

set the reference position.

Preparation Before Operation

01_EN_3P552666-6B.indd   9

07-May-19   1:00:18 PM

Summary of Contents for FTXM50UVMZ









































Reviews: