background image

English

5

English

Installation Tips

7) Wear protection gloves and insert both hands 

under the front grille as shown in the figure. 

8) Remove the front grille from the 3 upper hooks 

by pushing up the top side of the front grille, pull 
the front grille toward you by holding both ends 
of the front grille, and dismount the front grille.
• If the grille is hard to remove, insert a long flat 

plate* through the gap in the side cover as 
shown in the figure, and turn the plate inwards 
to disengage the hooks (3 hooks each on the 
right and left sides) so that you can remove the 
grille easily.
* Such as a ruler wrapped in a cloth

CAUTION

Be sure to wear protection gloves.

• Installation method 

1) Install the front grille and firmly engage the upper hooks (3 locations), right and left sides hooks (each 3 locations). 
2) Install 4 screws of the front grille, and close the 2 screw covers.
3) Mount the flap (large).
4) Lower the lower front panel to the original position.
5) Attach the wire harnesses to the 2 connectors and secure the wire harnesses with the wire clamp.
6) Install the air filter and then mount the upper front panel.

3.

How to set the different addresses

When two indoor units are installed in one 
room, the two wireless remote controllers can 
be set for different addresses. 

1) Remove the upper front panel and front 

grille. (4 screws) 

2) Cut the address jumper (JA) on the printed 

circuit board.

3) Cut the address jumper (J4) in the remote 

controller.
• Be careful not to cut jumper (J8).

4.

When connecting to an HA 
system 
(wired remote controller, central remote controller etc.)

• Removal methods of metal plate 

electrical wiring covers

 

1) Remove the upper front panel and front 

grille. (4 screws)

2) Remove the electrical wiring box. (1 

screw)

3) Remove the 4 tabs and dismount the metal 

plate electrical wiring cover (A).

4) Pull down the hook on the metal plate 

electrical wiring cover (B), and remove a 
single tab.

5) Remove the 2 tabs on the top part and 

dismount the metal plate electrical wiring 
cover (B). 

Upper hooks

2)Pull toward you.

1)Push up.

Side hooks

1
2

JA

[Indoor unit]

<Bottom of electrical wiring box>

INTELLIGENT EYE sensor

[Remote controller]

Jumper

(J8)

(J4)

ADDRESS
EXIST

CUT

ADDRESS : JA
EXIST : 1
CUT : 2

Metal plate electrical 
wiring cover (B)

Metal plate electrical 
wiring cover (A)

Screw

[From back side]

Single tab

Pull down

Summary of Contents for FTXJ20MV1BS

















Reviews: