background image

English

9

English

Indoor Unit Installation

4.

Laying piping, hoses, and wiring 

• The recommended installation method is back piping. 

When performing bottom piping or side piping, refer to 
“5. Bottom or side piping” on page 10.

4-1. Right-back piping 

1) Attach the drain hose to the underside of the refrigerant pipes with 

adhesive vinyl tape.

2) Wrap the inter-unit wire, refrigerant pipes and drain hose together 

with insulation tape.  

3) Pass the inter-unit wire, drain hose and refrigerant pipes through the 

wall hole, then set the indoor unit on the mounting plate hooks by using the   
markings at the top of the indoor unit as a guide. 

4-2. Left-back piping 

1) Replace the drain plug and drain hose. 
2) Attach the drain hose to the underside of the refrigerant 

pipes with adhesive vinyl tape.

3) Be sure to connect the drain hose to the drain port in place 

of a drain plug.

4) Shape the refrigerant pipe along the pipe path marking on the mounting plate. 
5) Pass drain hose and refrigerant pipes through the wall hole, then set the indoor unit on mounting plate hooks, using 

the   markings at the top of indoor unit as a guide. 

6) Pull in the inter-unit wire. 
7) Connect the inter-unit pipes.
8) Wrap the refrigerant pipes and drain hose 

together with insulation tape as shown in the 
figure on the right (in case of setting the drain 
hose through the back of the indoor unit).

Left back piping

Right back piping

Bind refrigerant pipe and drain hose 
together with adhesive vinyl tape.

A Mounting plate

Replacing onto the left side

1) Remove the insulation fixing screw on the right 

and remove the drain hose.

2) Remove the drain plug on the left side and 

attach it to the right side.

3) Insert the drain hose and tighten with included 

insulation fixing screw. Forgetting to tighten this 
may cause water leakages.

How to replace the drain plug and drain hose

Drain hose attachment position

The drain hose is on the back of the unit.

Front side of unit

Attachment on the right side 
(factory default)

Attachment on the left side

Drain hose

Drain hose

Insulation 
fixing screw

Insulation 
fixing screw

Right side

Left side

How to set drain plug

No gap

Insert a hexagonal wrench (4mm).

Do not apply lubricating oil (refrigerant 
oil) to the drain plug when inserting it.
The application of lubrication oil to the 
drain plug will deteriorate the plug to 
cause drain leakage from the plug.

Drain hose

Bind with 
adhesive 
vinyl tape.

A Mounting plate

Caulk this hole 
with putty or 
caulking material.

Wrap insulating tape around the bent portion 
of refrigerant pipe. 
Overlap at least half the width of the tape 
with each turn.

Summary of Contents for FTXJ20MV1BS

















Reviews: