background image

3

• Do not block air inlets nor outlets. Impaired air flow may result in insufficient performance or trouble.
• Do not stand or sit on the outdoor unit. Do not place any object on the unit to avoid injury, do not remove the fan guard.
• Do not place anything under the indoor or outdoor unit that must be kept away from moisture. In certain conditions, 

moisture in the air may condense and drip.

• After a long use, check the unit stand and fittings for damage.
• Do not touch the air inlet and aluminum fins of outdoor unit. It may cause injury.
• The appliance is not intended for use by young children or infirm persons without supervision.
• Young children should be supervised to ensure that they do not play with the appliance.

• To avoid oxygen deficiency, ventilate the room sufficiently if equipment with burner is used together with the 

air conditioner.

• Before cleaning, be sure to stop the operation, turn the breaker off or pull out the supply cord.
• Do not connect the air conditioner to a power supply different from the one as specified. It may cause trou-

ble or fire.

• Arrange the drain hose to ensure smooth drainage. Incomplete draining may cause wetting of the building, furniture 

etc.

• Do not place objects in direct proximity of the outdoor unit and do not let leaves and other debris accumulate around 

the unit. 
Leaves are a hotbed for small animals which can enter the unit. Once in the unit, such animals can cause malfunc-
tions, smoke or fire when making contact with electrical parts.

• Do not operate the air conditioner with wet hands.

• Do not wash the indoor unit with excessive water, only use a slightly wet cloth.
• Do not place things such as vessels containing water or anything else on top of the unit. Water may pene-

trate into the unit and degrade electrical insulations, resulting in an electric shock.

To install the air conditioner in the following types of environments, consult the dealer.

• Places with an oily ambient or where steam or soot occurs.
• Salty environment such as coastal areas.
• Places where sulfide gas occurs such as hot springs.
• Places where snow may block the outdoor unit.

The drain from the outdoor unit must be discharged to a place of good drainage.

For installation, choose a place as described below.

• A place solid enough to bear the weight of the unit which does not amplify the operation noise or vibration.
• A place from where the air discharged from the outdoor unit or the operation noise will not annoy 

your neighbours.

• For power supply, be sure to use a separate power circuit dedicated to the air conditioner.

• Relocating the air conditioner requires specialized knowledge and skills. Please consult the dealer if reloca-

tion is necessary for moving or remodeling.

Installation site.

Consider nuisance to your neighbours from noises.

Electrical work.

System relocation.

01_EN_3P208145-1E.fm  Page 3  Tuesday, April 22, 2008  1:55 PM

Summary of Contents for FTX20GV1B



























Reviews: