background image

6

Mounting Installation Plate

Ensure that the wall is strong enough to withstand the weight 
of the unit. Otherwise, it is necessary to reinforce the wall 
with plates, beams or pillars. 
Use the level gauge for horizontal mounting, and fix it with 
7 suitable screws.
In case the rear piping draws out, drill a hole 65mm in 
diameter with a cone drill, slightly lower on the outside wall 
(see figure).

Through the 

wall hole

Ø 65mm

190

173

61

310

61

Drain hose 

position

Gas pipe end

Liquid pipe end

48

45

580

1065

219

40

91

45

Water Drainage Piping

The indoor drain pipe must be in a downward gradient for 
smooth drainage. Avoid situations that are likely to cause 
water to leak.

Mounting plate

Clip

Mark (rear side)

Bottom frame

Front grille

Mount The Unit Onto The Installation Plate

Hook the indoor unit onto the upper portion of the installation 
plate (Engage the two hooks at the rear top of the indoor unit 
with the upper edge of the installation plate). Ensure that the 
hooks are properly seated on the installation plate by moving 
it to the left and right.

How To Attach The Indoor Unit

Hook the claws of the bottom frame to the mounting plate.

How To Remove The Indoor Unit

Push up the marked area (at the lower part of the front grille) 
to release the claws.

Mounting plate

Interconnecting 
wires

Hang indoor unit’s hook here.

Wire guide

When stripping the 
ends of interconnecting 
wires in advance, bind 
right ends of wires with 
insulating tape.

Recommended Mounting Plate Retention Spots And 
Dimensions

Inside

Caulking

Outside

Wall embedded pipe 
(Field supply)

Wall hole cover 
(Field supply)

Wall embedded pipe 
(Field supply)

Ø 65

  

Hole with cone drill

End dipped 
into water

Water leaking

Water leaking

Water leaking

Wrong

Wrong

Wrong

Drain

Water Drainage

Water Retention

Correct

Mounting plate

Mounting plate 

À

 xing screw

All dimensions are in mm

!

 CAUTION

• Do not install the unit at altitude over 2000m for both indoor and outdoor.

Recommended mounting plate 
retention spots (7 spots in all)

40

1-EN-IM WMJ-1111(0)Daikin.indd   6

11/29/11   2:04:43 PM

Summary of Contents for FTD20JEV1K





















Reviews: