5
Wiring diagrams
3D027501-1
FH35
∼
60BZ
1-RED, 2-WHITE, 3-BLACK
33A
Limit switch (swing flap)
A1P
Printed circuit board
A2P
Printed circuit board
(Transformer 220-240V/16V)
C1R
Capacitor (M1F)
F1U
Fuse (250V,5A)
HAP
Light emitting diode (service monitor green)
M1A
Motor (swing flap)
M1F
Motor (indoor fan)
Q1F
Thermo switch (M1F embedded)
R1T
Thermistor (air)
R2T
Thermistor (coil)
RyA
Magnetic relay (M1A)
RyC
Magnetic relay (outdoor unit compressor)
RyP
Magnetic relay (M1P)
SS1
Selector switch (emergency)
X1M
Terminal strip
X2M
Terminal strip
+
Current detect circuit
=
Phase control circuit
Wired remote control
R1T
Thermistor (air)
SS1
Selector switch (main/sub)
Infrared remote control
Receiver / display unit
A3P
Printed circuit board
A4P
Printed circuit board
BS
Push button (on/off)
H1P
Light emitting diode (service monitor red)
H2P
Light emitting diode (service monitor green)
H3P
Light emitting diode (service monitor red)
H4P
Light emitting diode (service monitor orange)
SS1
Selector switch (main/sub)
SS2
Selector switch (wireless address set)
Connector for optional parts
X15A
Connector (float switch)
X25A
Connector (drain pump)
X30A
Connector (interface adaptor for sky air series)
X33A
Connector (adaptor for wiring)
X35A
Connector (group control adaptor)
Switch box
To outdoor
unit
Note) 4
Wired remote
control
Note) 4
Notes
1.
D
: Terminal
F
,
H
: Connector
b
: Protective earth (screw)
2.
B
: Field wiring
3. In case using central remote controller, connect it to the
unit in accordance with the attached instruction manual.
4. X24A is connected when the remote controller kit is
being used.
5. Remote controller model varies according to the
combination system, confirm technical materials and
catalogs, etc. before connecting.
6. In case installing the drain pump, remove the jumper
connector of X15A and execute the additional wiring for
float switch and drain pump.
7. Ground the shield of the remote controller cord to the
indoor unit of the FH-BVE type.
8. Symbols show as follows Red:red, Blk:black, Ylw:yellow,
Org:orange, Gry:gray, Prp:purple, Blu:blue
9. Confirm the method of setting the selector switch (SS1,
SS2) by installation manual and engeneering materials,
etc.
Receiver / display unit
Note) 6
Note) 6
Note) 7
2TW21006-1C
FHY35
∼
45GZ7V1
33S
Limit switch (swing flap)
A1P
Printed circuit board
A2P
Printed circuit board (transformer 220-240V/16V)
C1R
Capacitor (fan)
H1P,H2P Light emitting diode
M1F
Motor
M1S
Motor
Q1F
Thermo switch (M1F embedded)
R1T
Thermistor (air)
R2T
Thermistor (coil)
RyA
Magnetic relay (swing flap)
RyP
Magnetic relay (drain pump)
SS1
Selector switch (emergency)
X1M,X2M Terminal strip
PC
Phase control circuit
RC
Signal receiver
TC
Signal transmission circuit
Connector for optional parts
X15A
Connector (float switch)
X25A
Connector (drain pump)
X30A
Connector (interface adaptor for sky air series)
X33A
Connector (adaptor for wiring)
X35A
Connector (group control adaptor)
Infrared remote control
BS1
On/Off button
BS2
Timer mode start/stop button
BS3,BS8
Programming time button
BS4,BS9
Temperature setting button
BS5
Air flow direction adjust button
BS6
Operation mode selector button
BS7
Timer on/off button
BS11
Fan speed control button
BS12
Inspection/test operation button
BS14
Filter sign reset button
H1P
Light emitting diode (service monitor red)
LCD
Liquid crystal display (LCD)
SS1
Selector switch (main/sub)
Adaptor for wiring
RyC,RyF
Magnetic relay
Outdoor
Wired remote
control
Terminals for operation
indicator
Fan
operation
compressor
operation
Notes
1. Use copper conductors only.
2. When using the central remote control, see
manual for connection to the unit.
3. The remote controller model varies according to
the combination system.
4. When installing the drain pump, remove the
jumper wire of X15A and make the additional
wiring for the float switch and the drain pump.
5. M1S and 33S are only attached to the indoor unit
of the heat pump type
g
Field wiring
D
Terminal
a
: Connector
c
: Wire clamp
b
: Protective earth (screw)
Colours
BLK: Black/ PPL: purple/ BLU: Blue/
WHT: White/ RED: Red/ GRN: green/
GRY: grey/ YLW:Yellow
Indoor
Note 4
Note 5
Details of wired remote control
(optional accessory)
(for heat pump type)
(for cooling only
type)
Adaptor for wiring
Switch box
Simultaneous operation system
Outdoor
unit
Remote control
(master)
(slave)
•
Ceiling Suspended Unit
•
R-407C
•
FH(Y)-GZ/BZ/FHYP-B
10
5
14
•
Split - Sky Air
•
Indoor Units
