background image

English

6

Micro computer automatically determines 
TEMPERATURE and FAN SPEED.

This system does not go into operation if the 
room temperature is below 16°C.

 Refer to figure 3 on page [1] 

For cooling only type, “COOLING”, “FAN” and 
“DRY” operation are able to select.

 ON/OFF

Press ON/OFF button

OPERATION lamp lights up or goes off and the sys-

tem starts or stops OPERATION.

[EXPLANATION OF HEATING OPERATION]

DEFROST OPERATION

As the frost on the coil of an outdoor unit increase, 
heating effect decreases and the system goes 
into DEFROST OPERATION.

The indoor unit fan stops and the remote control-
ler display shows “

”.

After 6 to 8 minutes (maximum 10 minutes) of 
DEFROST OPERATION, the system returns to 
HEATING OPERATION.

Regarding outside air temperature and heat-

ing capacity

The heating capacity of the air conditioner 
declines as the outside air temperature falls. In 
such a case, use the air conditioner in combina-
tion with other heating systems.

A warm air circulating system is employed, and 
therefore it takes some time until the entire room 
is warmed up after the start of operation.

An indoor fan runs to discharge a gentle wind 
automatically until the temperature inside the air 
conditioner reaches a certain level. At this time, 
the remote controller displays “

”. Leave it 

as it stands and wait for a while.

When the warm air stays under the ceiling and 
your feet are cold, we recommend that you use a 
circulator (a fan to circulate the air inside the 
room). For details, consult your dealer.

For programming TEMPERATURE, FAN SPEED 
and AIR FLOW DIRECTION, follow the procedure 
shown below.

TEMPERATURE SETTING 

Press TEMPERATURE SETTING button and 

program the setting temperature.

2

ADJUSTMENT

Each time this button is pressed, setting 
temperature rises 1°C.

Each time this button is pressed, setting 
temperature lowers 1°C.

The setting is impossible for fan operation.

NOTE

The setting temperature range of the remote con-
troller is 16 to 32°C.

FAN SPEED CONTROL

Press FAN SPEED CONTROL button.

High or Low fan speed can be selected.
The microchip may sometimes control the fan speed 
in order to protect the unit.

Operate in the following order.

The timer is operated in the following two ways.

Programming the stop time  (

) .... 

The system stops operating after the set time has 
elapsed.

Programming the start time (

) .... 

The system starts operating after the set time has 
elapsed. 

The timer can be programmed a maximum of 72 
hours.

The start and the stop time can be simultaneously 
programmed.

TIMER MODE START/STOP

Press the TIMER MODE START/STOP button 

several times and select the mode on the 

display.

The display flashes.
For setting the timer stop .... “

For setting the timer start .... “

PROGRAMMING TIME

Press the PROGRAMMING TIME button and 

set the time for stopping or starting the sys-

tem.

When this button is pressed, the time
advances by 1 hour.

When this button is pressed, the time
goes backward by 1 hour.

PROGRAM TIMER OPERATION

1

2

01_EN_3PN02535-7P.fm  Page 6  Friday, December 9, 2005  1:08 PM

Summary of Contents for FD(Y)M03FAV1(C)















Reviews: