background image

5 Application guidelines

Installer reference guide

16

EWAQ+005BAVP

Packaged air-cooled water chillers and packaged air to water heat

pumps

4P492900-1 – 2017.06

Combination: Under floor h Fan coil units -
Multiple rooms

Setup

e

B

C

A

d

M1

M1

b

a

c

A

Main leaving water temperature zone

B

Room 1

C

Room 2

a

User interface

b

Control box

c

Backup heater (option)

d

External room thermostat

e

Remote controller of the fan coil units

▪ For  each  room  with  fan  coil  units:  The  fan  coil  units  are  directly

connected to the outdoor unit – or to the backup heater, if there is
one.

▪ For each room with under floor heating: Two shut-off valves (field

supply) are installed before the under floor heating:

▪ A shut-off valve to prevent hot water supply when the room has

no heating demand

▪ A  shut-off  valve  to  prevent  condensation  on  the  floor  during

cooling operation of the rooms with fan coil units.

▪ For  each  room  with  fan  coil  units:  The  desired  room  temperature

is set via the remote controller of the fan coil units.

▪ For  each  room  with  under  floor  heating:  The  desired  room

temperature  is  set  via  the  external  room  thermostat  (wired  or
wireless).

▪ The main user interface (connected to control box EKCB07CAV3)

decides the space operation mode. Mind that the operation mode
of  each  external  room  thermostat  and  fan  coil  unit  remote
controller must be set to match that of the main user interface.

Configuration

Setting

Value

Unit temperature control:

▪ #: [A.2.1.7]

▪ Code: [C-07]

0 (LWT control): Unit operation is
decided based on the leaving
water temperature.

Number of water temperature
zones:

▪ #: [A.2.1.8]

▪ Code: [7-02]

0 (1 LWT zone): Main

5.3

Setting up an auxiliary heat source
for space heating

▪ Space heating can be done by:

▪ The outdoor unit

▪ An auxiliary boiler (field supply) connected to the system

▪ When  the  room  thermostat  requests  heating,  the  outdoor  unit  or

the  auxiliary  boiler  starts  operating  depending  on  the  outdoor
temperature  (status  of  the  changeover  to  external  heat  source).
When  the  permission  is  given  to  the  auxiliary  boiler,  the  space
heating by the outdoor unit is turned OFF.

▪ Bivalent operation is only possible for space heating.

INFORMATION

For  bivalent  operation  to  be  possible,  the  system  requires
option box EK2CB07CAV3.

INFORMATION

▪ During  heating  operation  of  the  heat  pump,  the

heat 

pump 

operates 

to 

achieve 

the 

desired

temperature  set  via  the  user  interface.  When  weather-
dependent operation is active, the water temperature is
determined  automatically  depending  on  the  outdoor
temperature.

▪ During  heating  operation  of  the  auxiliary  boiler,  the

auxiliary  boiler  operates  to  achieve  the  desired  water
temperature set via the auxiliary boiler controller.

Setup

▪ Integrate the boiler as follows:

b

a

c

d

d

i

i
j

j

m

f

h

g

k

l

e

FHL1

FHL2

FHL3

a

Outdoor unit

b

Heat exchanger

c

Pump

d

Shut‑off valve

e

Backup heater (option)

f

Control box

g

User interface

h

Option box

i

Non‑return valve (field supply)

j

Shut‑off valve (field supply)

k

Collector (field supply)

l

Auxiliary boiler (field supply)

m

Aquastat valve (field supply)

FHL1...3

Under floor heating

NOTICE

▪ Make sure the auxiliary boiler and its integration in the

system complies with applicable legislation.

▪ Daikin  is  NOT  responsible  for  incorrect  or  unsafe

situations in the auxiliary boiler system.

Summary of Contents for EWAQ004BAVP





























































































Reviews: