background image

2

REPLACEMENT PARTS

Ordering Parts

When reporting shortages or damages, or ordering repair 

parts, give the complete unit model and serial numbers as 

stamped on the unit’s nameplate. 

Replacement parts for this appliance are available through 

your contractor or local distributor. For the location of your 

nearest distributor, see website 

www.daikinac.com

 or 

contact:

EQUIPMENT SUPPORT

DAIKIN NORTH AMERICA LLC

19001 KERMIER ROAD

WALLER, TEXAS 77484

855-770-5678

SAFETY INSTRUCTIONS

  RECOGNIZE THIS SYMBOL AS 

  A SAFETY PRECAUTION. 

These installation instructions cover the 

outdoor 

installation of single package heating and cooling units.  

See the Specification Sheet applicable to your model for 

information regarding accessories.

*NOTE: Please contact your distributor or our 

website for the applicable Specification Sheet 

referred to in this manual.

To The Installer

Before installing this unit, please read this manual to 

familiarize  yourself on the specific items which must be 

adhered to, including maximum external static pressure to 

unit, air temperature rise, minimum or maximum CFM and 

motor speed connections. 

Keep this literature in a safe place for future reference.

CAUTION

Sheet metal parts, screws, clips and similar items inherently 

have sharp edges, and it is necessary that the installer and 

service personnel exercise caution.

WARNING

Do not connect to or use any device that is not design cer-

tified by the manufacturer for use with this unit. Serious 

property damage, personal injury, reduced unit perfor-

mance and/or hazardous conditions may result from the use 

of such non-approved devices.

WARNING

To avoid property damage, personal injury or death, do not 

use this unit if any part has been under water. Immediately 

call a qualified service technician to inspect the furnace 

and to replace any part of the control system and any gas 

control having been under water. 

WARNING

This unit must not be used as a “construction heater” during 

the finishing phases of construction on a new structure. 

This type of use may result in premature failure of the unit 

due to extremely low return air temperature and exposure 

to corrosive or very dirty atmospheres. 

WARNING

HIGH VOLTAGE!

Disconnect all power before servicing or in-

stalling this unit. Multiple power sources may 

be present. Failure to do so may cause proper-

ty damage, personal injury or death. 

WARNING

To prevent the risk of property damage, personal injury, or 

death, do not store combustible materials or use gasoline 

or other flammable liquids or vapors in the vicinity of this 

appliance. 

GENERAL INFORMATION 

WARNING

To prevent property damage, personal injury or death, 

due to fire, explosions, smoke, soot, condensation, elec-

tric shock or carbon monoxide, this unit must be properly 

installed, repaired, operated, and maintained. 

This unit is approved for outdoor installation ONLY

Rated performance is achieved after 20 hours of operation. 

Rated performance is delivered at the specified airflow.  

See product specification sheet for light commercial 

models. Specification sheets can be found at

 

 

www.daikinac.com for Daikin brand products. Within the 

website, please select the commercial products menu 

and then select the submenu for the type of product to be 

installed, such as air conditioners or heat pumps, to access 

a list of product pages that each contain links to that 

model’s specification sheet.

To assure that your unit operates safely and efficiently, it 

must be installed, operated, and maintained in accordance 

with these installation and operating instructions, all local 

building codes and ordinances.

Summary of Contents for DFC0361D













































Reviews: