manualshive.com logo in svg

Daikin 2MXS40H2V1B, Service Manual

Share
Download
Daikin 2MXS40H2V1B Service Manual Download Page 177

SiBE121123_A

Troubleshooting for RA Indoor Unit

Service Diagnosis

166

Troubleshooting

Check No.01

Refer to P.206

Check No.06

Refer to P.208

YES

YES

NO

NO

NO

NO

NO

(R18421)

YES

Caution

Replace the indoor electronic 
expansion valve coil.

Replace the thermistor.

∗

 Radiant panel thermistors

∗

 Indoor heat exchanger 

thermistor

∗

 Room temperature 

thermistor

Provide sufficient air passage.

YES

Check No. 01

∗

 Radiant panel thermistors

∗

 Indoor heat exchanger 

thermistor

∗

 Room temperature thermistor

Check the air passage.

Check the operation condition. 

Check the air filter.

OK?

As 

described in the 

thermistor characteristic 

chart?

Is there any short 

circuit?

YES

Clean the indoor heat 
exchanger.

Very dirty?

YES

Clean the air filter.

Very dirty?

NO

Completed.

Error repeats?

Be sure to turn off the power switch before connecting or disconnecting 
connectors, or parts may be damaged.

Check No. 06

Check the indoor electronic 
expansion valve coil.

YES

NO

Start operation within the 
specified range of the outdoor 
temperature.

Condition OK?

Check the indoor heat exchanger.

Replace the indoor unit PCB.

Change the refrigerant to remove 
moisture from the piping (after 
drawing a vacuum).

YES

NO

Completed.

Replace the indoor heat 
exchanger.

Error repeats?

∗

 

When the outdoor temperature is below the 
lower limit for cooling operation (10˚C), the 
freeze-up protection control is activated and the 
cooling operation stops.

Summary of Contents for 2MXS40H2V1B












































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands