background image

English

6

Refrigerant Piping Work

1.

Installing outdoor unit

1) When installing the outdoor unit, refer to “Precautions for Selecting the Location” on page 2 and the “Indoor/Outdoor Unit 

Installation Drawings” on page 3.

2) If drain work is necessary, follow the procedures below.

2.

Drain work (only heat pump models)

1) Use the drain plug for drainage.
2) If the drain port is covered by a mounting base or floor surface, place 

additional foot bases of at least 30mm in height under the outdoor 
unit’s feet.

3) In cold areas, do not use a drain hose with the outdoor unit.

(Otherwise, drain water may freeze, impairing heating performance.)

3.

Refrigerant piping

 CAUTION

• Use the flare nut fixed to the main unit. (To prevent cracking of the flare nut by aged deterioration.)
• To prevent gas leakage, apply refrigeration oil only to the inner surface of the flare. (Use refrigeration oil for R410A.)
• Use torque wrenches when tightening the flare nuts to prevent damage to the flare nuts and gas leakage.

Align the centres of both flares and tighten the flare nuts 3 or 4 turns by hand.  Then tighten them fully with the torque wrenches. 

Drain-water hole

Bottom frame

Drain plug

Hose (available commercially,
inner dia. 16mm)

Do not apply refrigeration 

oil to the outer surface.

Flare nut

Apply refrigeration oil to 

the inner surface of the 

flare.

Do not apply refrigeration oil to 

the flare nut to avoid tightening 

with excessive torque.

[Apply oil]

Flare nut tightening torque 

Flare nut for 

φ

6.4

14.2-17.2N 

l

 m

   

(144-175kgf 

l

 cm)

Flare nut for 

φ

9.5

32.7-39.9N 

l

 m

(333-407kgf 

l

 cm)

Flare nut for 

φ

12.7

49.5-60.3N 

l

 m

(505-615kgf 

l

 cm)

Valve cap tightening torque

Liquid side

3/8 inch

1/4 inch

21.6-27.4N 

l

 m

(220-280kgf 

l

 cm)

Gas side

1/2 inch

48.1-59.7N 

l

 m

(490-610kgf 

l

 cm)

21.6-27.4N 

l

 m

(220-280kgf 

l

 cm)

Service port cap tightening torque

10.8-14.7N 

l

 m (110-150kgf 

l

 cm)

01_EN_3P210724-1F.fm  Page 6  Tuesday, October 30, 2012  10:39 AM

Summary of Contents for 2MXS40G2V1B




















Reviews: