background image

Product Information

www.DaikinApplied.com 

IM 916-5 • MICROTECH COMMUNICATION MODULE

Light Emitting Diodes (LEDs)

The BACnet communication module has a BSP LED and a 

BUS LED to indicate communication activity and status of the 

BACnet communication module. These indicators are visible 

when the communication module is connected to the unit 

controller and the unit is powered on.

BSP LED

The BSP LED indicates the communication status between the 

BACnet communication module and the unit controller. 

Table 1

 

describes the status of the BSP LED.

Table 1: BSP LED Activity

BSP LED Color

Meaning

Flashing between 

 

Red and Green

Board Support Package (BSP) upgrade in progress

Green

Communication is established between the 

communication module and the unit controller

Yellow

The communication module is capable of 

communicating to the unit controller. However, 

communication is not established

Red flashing with 2Hz Red flashing with 2Hz = Software error

1

Red

Hardware error

1

1

 In the event that this should occur, cycle power to the unit controller to 

attempt to clear the problem. Contact the Controls Customer Support Group at 

866-462-7829 for additional assistance if necessary.

BUS LED

The BUS LED indicates the communication status between the 

BACnet communication module and the BACnet IP network. 

Table 2

 describes the status of the BUS LED.

Table 2: BUS LED Activity

BUS LED Color Meaning

Green

The unit controller is capable of communicating to the 

network

Red

The unit controller is not capable of communicating to the 

network

Orange / Yellow

Communication module is initializing

BACnet Network Connector

An RJ45 connector connects the BACnet communication 

module to the IP Network.

Board-to-Board Connector

The board-to-board connector connects the unit controller to 

the BACnet communication module (

Figure 3

 and 

Figure 4

).

Figure 3: Board-to-Board Connector 

 

   

Figure 4: Communication Module and Knockout       

Knockout 

permanently 

removed

Slot in module 

must

 line up 

with baffle in the board-to-

board connector

Board-to-board connector

Summary of Contents for 090016709













Reviews: