background image

General Information

www.DaikinApplied.com 

IM 916-5 • MICROTECH COMMUNICATION MODULE

General Information

 NOTICE

Use this manual to physically install the communication module into the 

unit controller and connect the Applied Air Handling unit controller to your 

network. Use the appropriate Engineering Data (ED), known as the Protocol 

Information document, to integrate the unit into your network. The Protocol 

Information document contains addressing details, BACnet protocol 

information, and a list of the data points available to the network. See 

the Reference Documents section of this manual for Protocol Information 

document numbers. Unit control integration literature is available from your 

local Daikin Sales Representative and www.DaikinApplied.com.

 NOTICE

This equipment generates, uses and can radiate radio frequency energy 

and, if not installed and used in accordance with this instruction manual, 

may cause interference to radio communications. It has been tested and 

found to comply with the limits for a Class A digital device, pursuant to 

part 15 of the FCC rules. These limits are designed to provide reasonable 

protection against harmful interference when the equipment is operated in a 

commercial environment. Operation of this equipment in a residential area 

is likely to cause harmful interference in which case the user will be required 

to correct the interference at his or her own expense. Daikin disclaims any 

liability resulting from any interference or for the correction thereof.

Hazardous Information Messages

 CAUTION

Cautions indicate potentially hazardous situations, which can result in 

personal injury or equipment damage if not avoided. 

 WARNING

Warnings indicate potentially hazardous situations, which can result in 

property damage, severe personal injury, or death if not avoided. 

 WARNING

Warning indicates potentially hazardous situations for PVC (Polyvinyl 

Chloride) and CPVC (Clorinated Polyvinyl Chloride) piping in chilled water 

systems. In the event the pipe is exposed to POE (Polyolester) oil used 

in the refrigerant system, the pipe can be chemically damaged and pipe 

failure can occur.

 

DANGER

Dangers indicate a hazardous electrical situation which will result in death 

or serious injury if not avoided.

 

DANGER

Dangers indicate a hazardous gas situation which will result in death or 

serious injury if not avoided.

 NOTICE

Notices give important information concerning a process, procedure, 

special handling or equipment attributes.

Revision History

IM 916

Oct 2008

Initial release

IM 916-1

May 2009

Modified Step 5 of “To Configure the Module using 

the Keypad/Display” section. Additional steps 

were added to describe how to properly set Given 

IP Address, Given IP Mask, or Given IP Gateway.

IM 916-2

Oct 2009

Added Maverick II (MPS) model. Additional 

changes to keypad display for new global 

navigation menu.

IM 916-3

Aug 2010

Removed note regarding about needing a 

crossover cable. Updated BSP in Table 1 to 

v1.1.30s.

IM 916-3

Mar 2012

•  Update Daikin logo and references. Added 

Rebel to cover.

•  Added step to turn OFF Control Mode on 

HMI prior to installing a new module on unit 

controller.

•  Removed NC Dev3 and RcvHrtBt from the 

Network Configuration Menu table these are no 

longer used.

•  Added AHU Loc/Net, Comm Status and 

RstOutOfSrvc to the Network Configuration 

Menu table

•  Changed BACnetBSP Initial Value in the 

Network Configuration Menu table to 9.26

IM 916-4

Dec 2019

Rebranded layout and added MicroTech 4 Rebel 

Applied. Other minor corrections.

IM 916-5

Aug 2020

OM 1288 added to Reference Documents

Reference Documents

Number

Company

Title

Source

ANSI/

ASHRAE 

135-2001

American Society 

of Heating, 

Refrigerating and 

Air-Conditioning 

Engineers

BACnet, a Data 

Communication 

Protocol for Building 

Automation and Control 

Networks

www.ashrae.org

OM 1288

Daikin Applied 

MicroTech 4 Rebel 

Applied™ Unit 

Controller Operation 

Manual

www.

DaikinApplied.

com

OM 920

MicroTech III Unit 

Controller Operation 

Manual for Applied 

Rooftop and Self-

Contained Systems

ED 19117

MicroTech 4 Rebel 

Applied Unit Controller 

Network Integration 

Guide, BACnet and 

LONWORKS Networks

ED 15112

MicroTech III Rooftop 

and Self Contained 

Unit Controller 

Network Integration 

Guide, BACnet and 

LONWORKS Networks

Limited Warranty

Consult your local Daikin Representative for warranty 

details. To find your local Daikin Representative, go to 

www.DaikinApplied.com.
Copyright ©2020 Daikin Applied Americas, Minneapolis MN. All 

rights reserved throughout the world.
Daikin reserves the right to change any information contained 

herein without prior notice. The user is responsible for 

determining whether this software is appropriate for his or her 

application.
®™ The following are tradenames or registered trademarks of 

their respective companies. BACnet from the American Society 

of Heating, Refrigerating and Air-Conditioning Engineers, 

Summary of Contents for 090016709













Reviews: