background image

Installation and Configuration Manual 

21 

4

 

System Configuration 

 

Configuring the Software 

4.1.1

 

Device initialization 

The  Camera  is  delivered  uninitialized  by  default.  You  need  to  initialize  it,  and  change  its  password 
before further operations. 

Before  initialization,  make  sure  that  both  PC  IP,  and  device  IP  are  on  the  same  network  segment, 
otherwise it might fail to enter the initialization page. 

Step 1  Set IP address, subnet mask, and gateway of PC, and device respectively. 

 

If there is no router in the network, distribute IP address of the same segment. 

 

If there is router in the network, configure the corresponding gateway, and subnet mask. 

The IP address is 192.168.1.108 by default. 

Step2 

Use ping ***. ***. ***. *** (device IP address) to check whether network is connected. 

Step 3  Open browser, enter the IP address of the Camera in the address bar, and then press the Enter 

key. 

 

Device initialization 

 

Step 4  Enter and confirm the password. 

 

 

The new password must consist of 8 to 32 characters, and contain at least two types from 
upper case, lower case, number, and special characters (excluding ' " ; :, and &). 

 

If  you  want  to  change  your  password  again,  go  to  Setting  >  System  >  Account  > 
Account

Summary of Contents for ITC413-PW4D Series












































Reviews: