Dahua HDCVI series User Manual Download

Page: 330 / 348

320



Please use the brush to clean the board, socket connector and the chassis regularly.



The device shall be soundly earthed in case there is audio/video disturbance. Keep

the device away from the static voltage or induced voltage.



Please unplug the power cable before you remove the audio/video signal cable,

RS232 or RS485 cable.



Do not connect the TV to the local video output port (VOUT).It may result in video

output circuit.



Always shut down the device properly. Please use the shutdown function in the menu,

or you can press the power button in the front pane for at least three seconds to shut

down the device. Otherwise it may result in HDD malfunction.



Please make sure the device is away from the direct sunlight or other heating sources.

Please keep the sound ventilation.



Please check and maintain the device regularly.

Summary of Contents for HDCVI series





























































































































































































































































































































































Search results

Summary of Contents for HDCVI series

Reviews:

Related manuals for HDCVI series

Brands by name

Popular brands

Dahua HDCVI series, User Manual

Search results

Summary of Contents for HDCVI series

Reviews:

Related manuals for HDCVI series

Brands by name

Popular brands