Dahua DH-TPC-BF5300 Operation Manual Download Page 65

Page: 65 / 101

Dahua IR Thermal Imaging Network Camera Web3.0 Operation Manual

Parameter

Note

Relay out

Check it to enable alarm activation output port, the system can activate
corresponding alarm output device when alarm occurs.

Alarm Delay

System can delay the alarm output for specified time after alarm ended. The value
ranges from 10s to 300s.

Send Email

If you enabled this function, System can send out email to alert you when

alarm occurs. User can set his email address in Network>SMTP.

Snapshot

You need to check the box here so that system can auto alarm snapshot when
alarm occurs. You shall set snapshot period in Storage>Schedule.

5.3.3 Temperature Alarm

Note:

Some models

don’t support temperature alarm function.

Figure 5-35

Parameter

Note

Enable

You need to check the box to enable alarm activation

Summary of Contents for DH-TPC-BF5300






































































































Search results

Summary of Contents for DH-TPC-BF5300

Reviews:

Related manuals for DH-TPC-BF5300

Brands by name

Popular brands

Dahua DH-TPC-BF5300, Operation Manual

Search results

Summary of Contents for DH-TPC-BF5300

Reviews:

Related manuals for DH-TPC-BF5300

Brands by name

Popular brands