manualshive.com logo in svg

Dahen DA300P, Owner'S Manual, Page: 18 / 85

Share
Download
Dahen DA300P Owner'S Manual Download Page 18

 

- 17 -

8.

CONNECTION PROCEDURE AND GROUND FOR SAFETY USE (continued) 

 
8.1.2 STICK WELDING 
 

The following figure shows the cable connections for stick welding with DC electrode positive 
(welding stick positive, base metal negative). When using DC electrode negative, switch the 
holder cable with the base metal cable. 

 

1. Ground the base metal (if required by local laws or codes). 
2. Connect the base metal cable to the negative 

٤

-  output terminal on the welding power 

source. 

3. Connect the holder to the positive 

٤

+   output terminal on the welding power source. 

 
8.2 Connecting of the Base Metal Cable and Stick Holder Cable 
 

When connecting the base metal cable and stick holder cable to the welding power source, 
attach the cable plug DIX SK 50 (supplied). 

 
 
 
 
 
 
 
 
 
 

Base metal cable

㧔

38mm

2

or more)

Firmly attach the base metal cable to the base metal.

Base metal

Welding cable

Holder

Groove

Cable

Biss

Grip

Sleeve

Connector

Conductor

٤

+

٤

㧙

Summary of Contents for DA300P






















































































Reviews:

No comments