Power Input:
110~250 Volts AC 50/60Hz
¡
120 Volts AC 60Hz
¡¡
Power Consumption:
17 Watts (2-head and 4-head)
Operating Temperature:
5 degree C to 40 degree C
(41 degree F to 104 degree F)
Storage Temperature:
-30 degree C to 65 degree C
(-22 degree F to 149 degree F)
Weight:
3.6 kg
Dimensions:
360mm Wide X 90mm High X
278mm Deep
Recording System:
4-head: Four video record/playback
heads
Rotary helical scan/luma: FM
recording/chroma: converted
subcarrier phase shifted recording
2-head: Two video/playback heads
Rotary helical scan/luma: FM
recording/chroma: converted
subcarrir phase shifted recording
Video head
¡
: K584NY-SJ/M, K584NZ-SJ/M,
K584NZ-SG/M
¡¡
: K584N-SJ, K584N-JJ, K584N-SG,
K484N-SJ, K484N-JJ, K484N-SG,
K384N-SJ, K284N-SJ, K504N-SJ,
K504NY-SG/X, K304N-SJ
Video Signal:
EIA standard; NTSC color
Antenna:
75 ohm input impedance
Video Signal Level:
1Vp-p (140 IRE standard)
Audio Input Impedance:
47k ohms
Audio Output
Impedance:
Less than 1.5k ohm
Tape Speed:
SP: 33.35mm/sec.
SLP: 11.13mm/sec
Maximum Recording Time: T-60: 3 hours/SLP mode
T120: 6 hours/SLP mode
Fast Forward/Rewind Time: 3 minutes (T-120 tape)
Tuning System:
Auto Program/Cable
Compatible/Frequency
Synthesis (FS)
Note: Specifications are subject to change without notice.
1
SPECIFICATIONS
Cleaning and Lubrication
A. Cleaning the Tape Transport System
The following parts should be cleaned after every 500 hours
of use.
• TENSION POLE
• S-GUIDE POST
• FE HEAD
• S GUIDE ROLLER
• S-SLANT POLE
• VIDEO HEAD/DRUM
• T-SLANT POLE
• T-GUIDE ROLLER
• AC HEAD/AE HEAD
• T-GUIDE POST
• CAPSTAN SHAFT
• PINCH ROLLER
Note: After cleaning with alcohol, allow the parts to dry thor-
oughly before using a cassette tape.
B. Cleaning the Drive System
The following parts should be cleaned after every 500 hours
of use.
• REEL TABLE
• T MAIN BRAKE
• S MAIN BRAKE
• T MAIN BRAKE
• CAPSTAN FLYWHEEL/PULLEY
• REEL PULLEY
C. Lubrication points
The following parts should be cleaned and lubricated after
every 500 hours of use. Apply one (1) or two (2) drops of oil.
Refer to the "Replacement Parts List" for the stock number of
the recommended oil.
• S REEL TABLE POST
• T REEL TABLE POST
• IDLER PULLEY
CLEANING AND LUBRICATION
Summary of Contents for DV- K584N-SJ
