background image

55

2) Audio circuit

1) Outline
This Audio Circuit use LA71004M A/V one chip IC of Sanyo's. The major feature of this IC is that has a Recording Bias current auto-
control circuit. So it is controlled by circuit automatically to keep consistent Recording current regardless change of head impedance.
Prior IC is used variable resistor to control Recording current passively.
But, variation range of HEAD Impedance has to be limited because of this auto-control circuit.

• R/P HEAD = 58 KOHM ± 15% (f = 70KHz) 
• A/E HEAD = 34 OHM ± 20%  (f = 70KHz) 

¢¡

Serial Type

= 180 OHM ± 20%  (f = 70KHz) 

¢¡

Parallel Type

• FE HEAD  = 80 OHM ± 15%  (f = 70KHz)

It can be devided a parallel and a serial circuit by form of connection of AE Head & FE Head. In case of D/W, we adopt a serial-type
circuit.

2) Name and operation of pins in audio IC

!

Features

i) 1 chip type including PB amp, Line Amp, REC amp, ALC circuit, EQ switch Auto REC bias circuit.

ii) It is equipped with EQ switch which operates in SP/LP/EP modes respectively.

iii) ALC level is fixed on-6dBv.

@

Function

Pin No

Name

Function

1

Auto-Bias-IN

320±10mVrms Input for auto-bias

2

EQ-SW2

Capacitor switch for head resonance in LP or EP SW ON

3

Auto-Bias-OUT

DC control voltage for auto-bias

4

Auto-Bias

Auto-Bias

5

EQ-IN

Line input, Input impedance: 120k

6

EQ-NFB

Negative Feedback of PB Amp

7

EQ-SW1

Playback equalizer switch in SP mode SW ON

8

EQ-OUT

Playback Amp out

9

Line-BP-IN

Line Amp input of playback Amp out

54

Mute ON/OFF

Mute control

55

PB/EE

PB/EE mode control

56

Audio REC/EE/PB

REC/EE control

57

Line IN

Line/Tuner input

58

ALC-DET

Port for ALC filter (setup attact or recovery time)

59

Line OUT

Line Amp out

60

REC IN

Input to REC Amp

61

Vcc

Vcc

62

Vref Filter

Vref filter (Ripple filter)

63

GND

GND

64

REC-OUT

Recording Amp out

Summary of Contents for DV- K504N-SJ




























































































































Reviews: