CONNECTIONS
13
12
Connections
Choose one of the following TV connections, depending on the capabilities of your equipment.
RF Connection
Connect the RF OUT (TO TV) jack on the DVD RVCR to the antenna in jack on your TV using the supplied
75-ohm RF cable (R). If you use this connection, tune your TV to the DVD RVCR's RF output channel
(CH52).
Scart Connection
1
Plug a scart cable into the scart socket EURO AV1 at
the back of the DVD RVCR and the
corresponding scart socket at the back of the TV set.
(V)
2
Plug a scart cable into the blue scart socket EURO
AV2/DECODER at the back of the DVD RVCR
and the corresponding scart socket at the back of a
satellite decoder or set top box.
S-Video Connection
1
Connect the S-VIDEO OUT jack on the DVD
RVCR to the S-Video in jack on your TV using
an S-Video cable (S).
2
Connect the Left and Right AUDIO OUT jacks from the DVD RVCR to the left/right audio in jacks on
your TV using the supplied audio cables.
Component Video Connection
1
Connect the COMPONENT/PROGRESSIVE VIDEO OUT jacks on the DVD RVCR to the corresponding
input jacks on your TV using a Y Pb Pr cable (C) if the Component Video jacks (Y, Pb, Pr) are available on
your TV.
2
Connect the Left and Right AUDIO OUT jacks from the DVD RVCR to the left/right audio in jacks on
your TV using the supplied audio cables.
Progressive Scan Connection
• If your television is a high-definition or ‘digital ready‘ television, you may take advantage of the DVD
RVCR’s Progressive Scan output for the highest video resolution possible.
• If your TV does not accept the Progressive Scan format, the picture will appear scrambled.
1
Connect the COMPONENT/PROGRESSIVE VIDEO OUT jacks on the DVD RVCR to the corresponding
in jacks on your TV using an optional Y Pb Pr cable (C).
2
Connect the Left and Right AUDIO OUT jacks from the DVD RVCR to the left/right audio in jacks on
your TV using the supplied audio cables.
Connecting a TV
• Be sure to set the DVD RVCR to Progressive Scan mode by pressing and holding [P.SCAN] for 3 seconds
(or changing the Video Output in the Setup Menu; see page 23).
• Progressive Scan does not work with the RF, Audio/Video or S-Video connections.
ANTENNA
INPUT
Y
Pb
Pr
COMPONENT/PROGRESSIVE VIDEO INPUT
S-VIDEO
INPUT
R
V
S
C
Rear of DVD RVCR
Rear of TV
Connections
Connections
Connecting Antenna/Cable
1
Disconnect the antenna/cable from the rear of your TV.
2
Connect this cable to the jack marked ANT IN (FROM ANT.)
on the rear panel of the DVD RVCR.
If your cable wire is connected to your TV without a converter or descrambler box, unscrew the wire from your
TV and attach it to the ANT IN (FROM ANT.) jack on the rear panel of the DVD RVCR.
Use the supplied coaxial cable to connect between the DVD RVCR’s OUT (TO TV) jack and the antenna
input jack on your TV. With this connection, you can receive all midband, superband, and hyperband channels
(all cable channels).
• There are a variety of ways to connect the DVD RVCR to your TV and other equipment. Use only one of
the connections described below. Whichever TV connection you use will work with all input sources.
• Please refer to the manuals for your TV, VCR, stereo system, or other devices as necessary to make the best
connections.
• For better sound reproduction, connect the DVD RVCR’s AUDIO OUT jacks to the audio in jacks of your
amplifier, receiver, stereo, or audio/video equipment. See ‘Connecting an Amplifier/Receiver‘ on page 13.
Caution
• Make sure the DVD RVCR is connected directly to the TV, and the TV is set to the correct video input.
• Do not connect the DVD RVCR’s AUDIO OUT jack to the phono in jack (record deck) of your audio system.
• Do not connect the DVD RVCR via your VCR. The DVD image could be distorted by the copy protection
system.
Rear of DVD RVCR
Antenna
Antenna
Cable TV
Wall Jack
Flat Wire
(300ohm)
300/75ohm Adapter
(Not supplied)
OR
OR
