Daewoo DBC430AV User Manual Download Page 13 | Manualshive

Page: 13 / 24

background image

12

For COLD start set the choke lever to the ON position by moving upwards as shown.
For a WARM start keep the choke lever at the OFF position.

Place one hand on the machine, and using the other hand pull the recoil until you feel a
resistance, then pull briskly. Repeat until machine starts. When the machine starts move the
choke to the OFF position. DO NOT let go of the recoil handle instead allow the recoil cord and
handle return slowly.

«
...
11
12
13
14
15
...
»

Summary of Contents for DBC430AV

























Reviews:

No comments

Related manuals for DBC430AV

Brand: Echo Pages: 9

ColorCut Flatbed FB1060 Series

Brand: Intec Pages: 50

Brand: P.Lindberg Pages: 111

Brand: QUINN Pages: 8

Brand: Vivo Pages: 8

Brand: Husqvarna Pages: 36

Brand: Land Pride Pages: 92

Brand: SMASH Pages: 102

TMC24 TURF multi Cutter

Brand: Groundsman Pages: 22

Classen HSC18HD

Brand: Schiller Pages: 47

Brand: FangLing Pages: 147

Brand: Danfoss Pages: 50

Brand: Zenoah Pages: 36

Brand: Vari Pages: 36

Brand: PAPILLON Pages: 42

Brand: Garland Pages: 144

GT-2150_SI(6digits)(35)(36)

Brand: Echo Pages: 28

Brand: NARGESA Pages: 54

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands