Daewoo DBC430AV User Manual Download Page 11 | Manualshive

Page: 11 / 24

background image

10

2.12. Mixing two stroke oil.
Fill the mixing bottle with fresh unleaded petrol to the fuel level line. For the first fill use the
ratio of 25:1 thereafter use a ratio of 40:1.

2.13. Adding fuel.
Unscrew the fuel tank cap and carefully add a fuel/2 stroke oil mixture as in section 2.12. DO NOT
overfill and allow a 25 mm gap at the top of the tank. Once full replace and correctly tighten the fuel
cap. DO NOT use straight unleaded petrol.

«
...
9
10
11
12
13
...
»

Summary of Contents for DBC430AV

























Reviews:

No comments

Related manuals for DBC430AV

Brand: SPEWE Pages: 10

Brand: Sawyer Pages: 4

Brand: EL-CELL Pages: 7

Brand: Worx Pages: 36

Brand: Inter Laser Pages: 50

Brand: Tupperware Pages: 12

Brand: Ilco Orion Pages: 24

Brand: Maruyama Pages: 20

Brand: Royal Catering Pages: 17

Brand: EINHELL Pages: 32

Brand: EINHELL Pages: 46

Brand: Oce Pages: 23

Brand: Vari Pages: 36

Brand: GARDEO PRO Pages: 109

ABSS18-1.6 E Series

Brand: Fein Pages: 194

Brand: Makita Pages: 40

Brand: Hitachi Pages: 38

Brand: CanyCom Pages: 94

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands